Rear Tail Light Harness - Harley Davidson Forums



Touring Models Road King, Road King Custom, Road King Classic, Road Glide, Street Glide, Electra Glide, Electra Glide Classic, and Electra Glide Ultra Classic bikes.
Sponsored by: Fuel Moto USA

Rear Tail Light Harness

Reply
 
 
 
P
 
Thread Tools Search this Thread
  #1  
Old 01-20-2010, 02:02 PM
cybermunster's Avatar
cybermunster cybermunster is offline
Road Master
Thread Starter
Join Date: Oct 2007
Location: South Florida
Posts: 1,249
Thanks: 0
Thanked 0 Times in 0 Posts
Default Rear Tail Light Harness

As some of you may have seen by a previous post I made I recently did some work on the rear of my '08 FLHTC and while there discovered that the rear tailight harness which is attached to the underside of the rear fender was chewed out pretty bad by the tire when the bike was bottoming out badly.
I taped everything up and did the best I could but would like to replace the harness and do it right.
I go to my "trusty" dealer's parts guy and he informs me I have to buy basically the entire wiring harness and it's $588.00 ...
So I come back home and check the harness (from the underseat plug to the rear tailight) and get a part number #68772-06 which goes for $19.20!!
Now before I can believe this does anyone has or knows where can I get a diagram of the harness part #68772-08?

Greatly appreciated and maybe Dawg or Doc can help me on this one also.

Later guys.

Last edited by cybermunster; 01-20-2010 at 02:04 PM.
Reply With Quote
  #2  
Old 01-20-2010, 02:24 PM
frenchbiker's Avatar
frenchbiker frenchbiker is offline
Elite HDF Member
Join Date: Apr 2006
Location: The Burgh
Posts: 3,578
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I have an 09 Ultra and the 09 Service manual. It's figure B-27 in the manual. The rear harness is the same as yours 68772-06, with 6 pins. The tail lamp has a 4 pin connector (type 93B-93A) with Black (Ground pin #4), Red/Yellow(Brake light pin #3), Orange/White( Running light HDI (International) pin#2) and Blue/White(Running light DOM (Domestic) pin#1).

Unfortunately I don't have a scanner

What else do you want to know?

Last edited by frenchbiker; 01-20-2010 at 02:32 PM.
Reply With Quote
  #3  
Old 01-20-2010, 03:16 PM
Skip Skip is offline
Road Captain
Join Date: Apr 2006
Location: Erhard, MN
Posts: 517
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I have had this happen on a couple of different bikes. Just pulled the harness loose, cut out the bad spots, soldered in new wire where needed, wrapped in electrical tape, and then covered with flexible plastic conduit. Still working.
Reply With Quote
  #4  
Old 01-20-2010, 03:44 PM
hog-doc's Avatar
hog-doc hog-doc is offline
Road Warrior
Join Date: Feb 2009
Location: ID Ho
Posts: 1,723
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Skip View Post
I have had this happen on a couple of different bikes. Just pulled the harness loose, cut out the bad spots, soldered in new wire where needed, wrapped in electrical tape, and then covered with flexible plastic conduit. Still working.
Or do it right and get the connectors from either the dealer or Namz and replace the entire damaged wire, crimp on new connectors and be as good as factory.

Because I did the same thing, (rubbed the wires bare, repaired as above) Iam considering rerouting them outside the fender like the 2010 SG/RG and curing the problem!
Reply With Quote
  #5  
Old 01-20-2010, 04:02 PM
dawg's Avatar
dawg dawg is offline
Club Member
Join Date: Jun 2006
Location: Vermont
Posts: 20,968
Thanks: 0
Thanked 16 Times in 16 Posts
Default

Reply With Quote
  #6  
Old 01-20-2010, 04:05 PM
Maimas's Avatar
Maimas Maimas is offline
Road Warrior
Join Date: Feb 2009
Location: East Northport, NY
Posts: 1,661
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Are you sh!tt!ng me!!! $588.00 for about 3' of wire and some plastic plugs?
Reply With Quote
  #7  
Old 01-20-2010, 04:30 PM
cybermunster's Avatar
cybermunster cybermunster is offline
Road Master
Thread Starter
Join Date: Oct 2007
Location: South Florida
Posts: 1,249
Thanks: 0
Thanked 0 Times in 0 Posts
Default

According to this parts guy they don't sell just that part I would have to buy basically the entire wiring harness!!! ...needless to say I quietly and hurriedly walked away and won't go back, what a joke ...$588.00!! ..musta been smokin' some really good chit.
Anyway I'd rather replace than repair as theres about a 8"~9" piece of the protective sheath missing.
Reply With Quote
  #8  
Old 01-20-2010, 04:33 PM
cybermunster's Avatar
cybermunster cybermunster is offline
Road Master
Thread Starter
Join Date: Oct 2007
Location: South Florida
Posts: 1,249
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Dawg ..is the area I circled in red the harness/wire snake from the underseat plug to the rear tailight? Would this "wire snake" be part #68772-06?
Also this wire snake is inside a plastic protective sheath under the rear fender I'm assumming this sheath is glued to the fender as I see no clips or fasteners.
Attached Thumbnails
Rear Tail Light Harness-rearlights.jpg  

Last edited by cybermunster; 01-20-2010 at 04:37 PM.
Reply With Quote
  #9  
Old 01-20-2010, 04:49 PM
Maimas's Avatar
Maimas Maimas is offline
Road Warrior
Join Date: Feb 2009
Location: East Northport, NY
Posts: 1,661
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Yeah... Mine was held in with double sided tape. When I changed my tins, I made sure I brought it inside where it was warm before I put it on. Havent had any problems with mine coming loose.
Reply With Quote
  #10  
Old 01-20-2010, 05:52 PM
pled55's Avatar
pled55 pled55 is offline
Road Master
Join Date: Oct 2007
Location: so.jersey
Posts: 808
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by cybermunster View Post
As some of you may have seen by a previous post I made I recently did some work on the rear of my '08 FLHTC and while there discovered that the rear tailight harness which is attached to the underside of the rear fender was chewed out pretty bad by the tire when the bike was bottoming out badly.
I taped everything up and did the best I could but would like to replace the harness and do it right.
I go to my "trusty" dealer's parts guy and he informs me I have to buy basically the entire wiring harness and it's $588.00 ...
So I come back home and check the harness (from the underseat plug to the rear tailight) and get a part number #68772-06 which goes for $19.20!!
Now before I can believe this does anyone has or knows where can I get a diagram of the harness part #68772-08?

Greatly appreciated and maybe Dawg or Doc can help me on this one also.

Later guys.



did you do any mods to your suspension to cause this damage to your wires?
Reply With Quote
 
 
 
P
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Fat Bob Main Harness. Rubline Electrical/Lighting/Alarm 2 08-26-2016 05:33 AM
Fender Swap FrankieK Touring Models 1 08-11-2016 04:17 PM
Road King main wire harness WhoRidaz Electrical/Lighting/Alarm 0 03-29-2016 01:32 AM
Correct installation of new brake light on chopped fender... Julie65 Sportster Models 17 05-28-2014 06:08 PM
Any tips to help me remove my wiring harness on 05 and older Dyna? parts eeter Dyna Glide Models 14 02-17-2014 01:13 PM


Tags
06, 09, 6877206, classic, diagram, harley, harleydavidson, harness, king, light, rear, replace, road, rod, tail, wiring

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -5. The time now is 08:37 PM.