Touring Models Road King, Road King Custom, Road King Classic, Road Glide, Street Glide, Electra Glide, Electra Glide Classic, and Electra Glide Ultra Classic bikes.
Sponsored by:
Sponsored by:

Eglide CVO, cruise not working

Thread Tools
 
Search this Thread
 
  #1  
Old 02-15-2022, 03:44 PM
mgb1's Avatar
mgb1
mgb1 is offline
Cruiser
Thread Starter
Join Date: Apr 2010
Location: S.C.
Posts: 134
Received 12 Likes on 9 Posts
Default Eglide CVO, cruise not working

The cruise control on my '04 Eglide CVO has not worked in quite a while and I need to get if fixed. Anyone have a good prodcedure to test it etc.? Both the front and rear brakes seem to work well and the brake light does stay on at all when the brake pedal and lever are released. I did go through a procedure that a member on here said worked on '05 FLH and it did not work on mine. Anyone out there have a similar problem and a fix? Thanks
 
  #2  
Old 02-15-2022, 03:49 PM
asa1199's Avatar
asa1199
asa1199 is offline
Tourer

Join Date: Oct 2012
Location: New Jersey
Posts: 292
Received 83 Likes on 43 Posts
Default

Brake light stays on? You need to fix that first.
 
The following users liked this post:
smitty901 (02-15-2022)
  #3  
Old 02-15-2022, 03:53 PM
smitty901's Avatar
smitty901
smitty901 is offline
Seasoned HDF Member

Join Date: Feb 2008
Posts: 22,185
Received 9,561 Likes on 5,153 Posts
Default

See above post.
Brake light staying on will not allow cruise to work.
 
  #4  
Old 02-15-2022, 05:36 PM
GalvTexGuy's Avatar
GalvTexGuy
GalvTexGuy is offline
Seasoned HDF Member

Join Date: Apr 2015
Location: SE Tejas
Posts: 8,140
Received 3,942 Likes on 2,164 Posts
Default

I think he forgot “not”.

“…the brake light does not stay on at all when the brake pedal and lever are released.”
 
  #5  
Old 02-15-2022, 07:43 PM
mgb1's Avatar
mgb1
mgb1 is offline
Cruiser
Thread Starter
Join Date: Apr 2010
Location: S.C.
Posts: 134
Received 12 Likes on 9 Posts
Default

Yep, what Tex said. I left out the NOT. Tex, thanks for reading between the lines.
 
The following users liked this post:
GalvTexGuy (02-15-2022)
  #6  
Old 02-15-2022, 07:48 PM
Hoginedgewood's Avatar
Hoginedgewood
Hoginedgewood is offline
Stellar HDF Member
Join Date: Jul 2017
Location: Ky
Posts: 3,182
Received 1,190 Likes on 652 Posts
Default

Originally Posted by mgb1
The cruise control on my '04 Eglide CVO has not worked in quite a while and I need to get if fixed. Anyone have a good prodcedure to test it etc.? Both the front and rear brakes seem to work well and the brake light does stay on at all when the brake pedal and lever are released. I did go through a procedure that a member on here said worked on '05 FLH and it did not work on mine. Anyone out there have a similar problem and a fix? Thanks
from what I've read it's usually the throttle cable that has a wire to it. Not sure if disconnected is the test or grounding it. I have a brand new module that has never been installed if you get to that point. It was for my 06.
 
  #7  
Old 02-17-2022, 08:10 AM
LRS's Avatar
LRS
LRS is offline
Tourer
Join Date: Sep 2009
Location: Georgia
Posts: 490
Received 170 Likes on 83 Posts
Default

I just went through this on my 06. Do this test to see if clutch lever, brake lever or pedal and roll off switch is working. Hopefully its one of these components causing failure.


Mine was none of the above. It would work intermittently. My green light would always light up, as if my cruise was all working but it was not. Mine was the cruise module. They are no longer available new for our era bikes and they say its a non serviceable part. I found one from a low mileage wreck on ebay from Fallen cycles. Even used they are not cheap. I put it on my bike and cruise works flawlessly.
I will say, I took my old one apart and inside it was full of oxidation/ corrosion. I cleaned it all with electrical contact cleaner. I have a feeling it may work after that but never went through testing it. Module is located under left side cover.
 
  #8  
Old 03-19-2022, 09:57 PM
mgb1's Avatar
mgb1
mgb1 is offline
Cruiser
Thread Starter
Join Date: Apr 2010
Location: S.C.
Posts: 134
Received 12 Likes on 9 Posts
Default

FIXED IT!!!!! The problem was the throttle "roll back" switch was shorted. The vdeo at......
...... put me right onto it .Works as it should now.
 
The following 3 users liked this post by mgb1:
GalvTexGuy (03-20-2022), OkieBill (03-20-2022), skratch (03-20-2022)
  #9  
Old 03-20-2022, 10:52 AM
OkieBill's Avatar
OkieBill
OkieBill is offline
Club Member

Join Date: Sep 2014
Location: NE Oklahoma
Posts: 749
Received 424 Likes on 258 Posts
Default

Gotta love the simplicity of this fix action. Very cool 😎
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Xcrossbow
Frame/Suspension/Front End/Brakes
11
06-12-2022 05:34 PM
Martyrittenhouse
Frame/Suspension/Front End/Brakes
11
09-11-2020 01:55 PM
JONNIEROCK
Touring Models
1
07-06-2018 10:24 AM
Mofo67
Touring Parts
1
06-08-2018 12:37 PM
jkane13
2014-2023 Touring Models
58
10-14-2014 08:10 PM



Quick Reply: Eglide CVO, cruise not working



All times are GMT -5. The time now is 03:30 AM.