Finally had a chance to work on the bike 2012 Superglide
#1
Finally had a chance to work on the bike 2012 Superglide
Weather has been down right stupid around here, so much so I have not been able to get into the garage to work, but late last week It finally cooled down enough to do so...well...what did I do?
New front wheel/tire & EBC chrome rotor (17" chrome spoke to match the rear) 140 tire
Predator motor mount
Installed rocker lockers
Hayden primary chain adjuster
Redid my EBC lines
New plugs
All 3 oil change
New rear tire - cleaned the rear brake caliper
Installed (new to me) rear shocks (Fatbob)
Polished a bunch of fasteners...(to cheap to buy chrome bolts)
all tins out for new paint
Whats left...change grips, and a few minor things to button it all up...
Attachment 618283
Attachment 618284
I was able to get a couple of those touring spacers for free from my local shop and I polished them up....
and of course the rear of the bike with new tire, and fatbob shocks...
Attachment 618285
New front wheel/tire & EBC chrome rotor (17" chrome spoke to match the rear) 140 tire
Predator motor mount
Installed rocker lockers
Hayden primary chain adjuster
Redid my EBC lines
New plugs
All 3 oil change
New rear tire - cleaned the rear brake caliper
Installed (new to me) rear shocks (Fatbob)
Polished a bunch of fasteners...(to cheap to buy chrome bolts)
all tins out for new paint
Whats left...change grips, and a few minor things to button it all up...
Attachment 618283
Attachment 618284
I was able to get a couple of those touring spacers for free from my local shop and I polished them up....
and of course the rear of the bike with new tire, and fatbob shocks...
Attachment 618285
Last edited by crusader1xxx; 07-12-2019 at 07:02 PM.
#3
Join Date: Dec 2007
Location: Lake City, Florida (Native)
Posts: 9,255
Received 279 Likes
on
214 Posts
The following users liked this post:
crusader1xxx (08-08-2019)
#4
Weather has been down right stupid around here, so much so I have not been able to get into the garage to work, but late last week It finally cooled down enough to do so...well...what did I do?
New front wheel/tire & EBC chrome rotor (17" chrome spoke to match the rear) 140 tire
Predator motor mount
Installed rocker lockers
Hayden primary chain adjuster
Redid my EBC lines
New plugs
All 3 oil change
New rear tire - cleaned the rear brake caliper
Installed (new to me) rear shocks (Fatbob)
Polished a bunch of fasteners...(to cheap to buy chrome bolts)
all tins out for new paint
Whats left...change grips, and a few minor things to button it all up...
I was able to get a couple of those touring spacers for free from my local shop and I polished them up....
and of course the rear of the bike with new tire, and fatbob shocks...
New front wheel/tire & EBC chrome rotor (17" chrome spoke to match the rear) 140 tire
Predator motor mount
Installed rocker lockers
Hayden primary chain adjuster
Redid my EBC lines
New plugs
All 3 oil change
New rear tire - cleaned the rear brake caliper
Installed (new to me) rear shocks (Fatbob)
Polished a bunch of fasteners...(to cheap to buy chrome bolts)
all tins out for new paint
Whats left...change grips, and a few minor things to button it all up...
I was able to get a couple of those touring spacers for free from my local shop and I polished them up....
and of course the rear of the bike with new tire, and fatbob shocks...
The following users liked this post:
crusader1xxx (07-13-2019)
#6
It’s a “U” shaped bar that mounts through the center hole in the middle of the frame...same place you would mount a crash bar...I used 1/8” steel plate, cut to size, bent the ends and drilled holes for the lights..it’s just spray bombed just now, over the winter I’ll get it powder coated
The following 2 users liked this post by crusader1xxx:
JayStronghawk (07-15-2019),
Tall Timber (07-16-2019)
Thread
Thread Starter
Forum
Replies
Last Post