Ironhead A place to talk about Ironheads.

S&S Carbs

Thread Tools
 
Search this Thread
 
  #1  
Old 10-25-2007, 02:34 PM
CTP's Avatar
CTP
CTP is offline
Cruiser
Thread Starter
Join Date: Jul 2007
Location: North West Arkansas
Posts: 137
Likes: 0
Received 0 Likes on 0 Posts
Default S&S Carbs

Was at the Harley Shop ( not dealer) and was asking about the carburator on my 84 ironhead.
The guy said, its like this Kevin............buy an S&S carb and your problems are over as far as carburators go.........
What is everyones take on this? my bike has a Keihin carb on it ( Non CV ).
I just dont know so im looking for advice, also is the Keihin Non CV the factory carb?
Thanks
Kevin
 
  #2  
Old 10-25-2007, 04:21 PM
83XLX's Avatar
83XLX
83XLX is offline
Road Warrior
Join Date: Nov 2006
Location: Heart of Dixie
Posts: 1,385
Received 640 Likes on 228 Posts
Default RE: S&S Carbs

Yes, that's the stock carb. I have one on my '83 and have had absolutely no problems with it. If yours is OK, I'd leave well enough alone. If you need a new carb, the S&S is a proven performer but it will cost close to $400 for a new one with everything you need. I've heard that the CV Keihins are a good replacement, too.Used ones are pretty cheap, but you will have to adapt it to your manifold andget a new air cleaner to fit it.
 
  #3  
Old 10-26-2007, 10:07 AM
cruncher's Avatar
cruncher
cruncher is offline
Novice
Join Date: Oct 2007
Posts: 23
Likes: 0
Received 0 Likes on 0 Posts
Default RE: S&S Carbs

i have found that one of the cheapest replacment and a top preformers is the old VM mikuni 38 mm with a primary bleed needle the ones on two stroke dirt bikes and snowmobiles you well have to get a manifold adapter but they are easy to get for around $20
 
  #4  
Old 10-26-2007, 12:29 PM
jdusty21's Avatar
jdusty21
jdusty21 is offline
Advanced
Join Date: Jun 2007
Location:
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default RE: S&S Carbs

I have the cv carb on my 79 xls, works great, runs good, stays adjusted ( a little rich at idle) cheap and an easy adaption. Only draw back for me was the size.... it stuck out to far... I then replaced the fuel tank to a larger size (I had the sporty 2.2 gal tank) for apperance and distance (lol). It still sticks out too far for the highway pegs but I can live with that for a savings of over 250 from the S&S shorty carb. Also had to change the AC and make a bracket to support the carb and AC cover. Good Luck Dusty
 
  #5  
Old 10-26-2007, 01:21 PM
crampfan's Avatar
crampfan
crampfan is offline
Cruiser
Join Date: May 2007
Posts: 207
Likes: 0
Received 1 Like on 1 Post
Default RE: S&S Carbs

I have had Zero "0" problems with my S&S "E" on my 89 FLHover 90,000 miles and 17 years and I have not even had the float bowl off it. I have a "B" on my old panhead I've had to rebush the throttle shaft and replace the float. (over 25 yrs, and about 130,000 miles) me thinks S&S carbs. are worth every penny.
 
  #6  
Old 11-05-2007, 05:47 PM
Oldtimer of NM's Avatar
Oldtimer of NM
Oldtimer of NM is offline
Road Master
Join Date: Jan 2007
Location: East NM
Posts: 770
Likes: 0
Received 2 Likes on 2 Posts
Default RE: S&S Carbs

I have installed S&S carbs on several bikes and run them for years. The only carb that has given me less trouble was a Linkert, but Linkerts have so few parts that not much can go wrong and you don't get much performance with them either..
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
supermanotorious
Dyna Glide Models
16
03-25-2018 09:36 AM
dexterdave
Softail Models
3
06-10-2009 12:17 PM
artz
Sportster Models
49
09-19-2007 11:18 PM
flpops
Sportster Models
2
09-08-2007 09:47 AM
stone_rider420
Sportster Models
5
04-14-2007 11:03 AM



Quick Reply: S&S Carbs



All times are GMT -5. The time now is 09:31 PM.