06 FXD TC88 to 103..help - Harley Davidson Forums

Primary/Transmission/Driveline/Clutch Find answers to general powertrain, primary and transmission. Have clutch issues and need suggestions? Post them here.
Sponsored by:
Sponsored by:

06 FXD TC88 to 103..help

Reply

 
 
 
  #1  
Old 02-10-2018, 11:59 AM
abez's Avatar
abez
abez is offline
One Of The Regulars
Thread Starter
Join Date: Apr 2016
Location: Leesburg, VA
Posts: 129
Thanked 20 Times in 15 Posts
Default 06 FXD TC88 to 103..help

I was looking for some technical help regarding increasing power and compatibility when doing a motor swap.


I have a 2006 Dyna Streetbob with a TC88 FI motor with a newly rebuilt 6 speed tranny and the newer SE compensator. I was going to do the heads, cams and then I thought maybe Ill increase the cylinder size as well while I'm at it. while putting together a cost comparison, it looks like it may be comparable/cheaper and more dependable to acquire a 103 from an ebay vendor and swap my 88" for a 103".


I was wondering what I would need to do this swap?


Do I need a new ECM, Ill probably need the bigger throttle body and can I use a 103 out of a Touring Road/Street Glide in my Dyna mated to my 6 speed?
If the heads have ACR, could I probably wire it to the starter?
Is wiring going to be a nightmare or is my current wiring compatible with what I'd use on the 103?




really appreciate any help.
 
Reply With Quote
  #2  
Old 02-10-2018, 01:34 PM
Screamin beagle
Screamin beagle is offline
Road Captain
Join Date: Jun 2017
Location: Granville New York
Posts: 733
Thanks: 0
Thanked 176 Times in 127 Posts
Default

Disclaimer: I'm no expert. But I would think that it would way more cost effective and easier to go to a 98" build and pretty sure that a built 98 will outperform the 103 all day. Maybe I'm wrong and the swap would be a piece of cake but I think just for cost of acquiring a used 103, that's in what condition?, would be more than a decent 98" build.
 
Reply With Quote
  #3  
Old 02-13-2018, 05:31 AM
grbrown's Avatar
grbrown
grbrown is offline
Club Member
Join Date: Jun 2007
Location: Bedford UK
Posts: 39,399
Thanked 1,229 Times in 1,141 Posts
Cool

I'm not sure there were many models of TC88 that had a 103" engine. The TC96 model range has more models with a 103", but your trans won't bolt up to them, so that isn't going to work. In addition, Beagle's suggestion above will bring you many benefits over a stock 103", even if you have a slightly smaller capacity.

We have engine builders in here who you can contact for expert help, to actually perform mods and supply new parts. Pop into the Tech Engine section and consider contacting Scott at Hillside Cycle. Tell him you're a member of HDF! A proven aftermarket package should really light up your bike!
 
Reply With Quote
  #4  
Old 02-13-2018, 05:38 AM
QC's Avatar
QC
QC is offline
Club Member
Join Date: Mar 2012
Location: Centennial, CO
Posts: 57,523
Thanked 2,243 Times in 1,474 Posts
Default

Scott will fix you up. He won't sell you anything you don't want/need. Great guy to work with.
 
Reply With Quote
  #5  
Old 02-13-2018, 07:09 AM
Nomadmax's Avatar
Nomadmax
Nomadmax is offline
Ultimate HDF Member
Join Date: Aug 2011
Location: SW Ohio, On the bank of Big Twin Creek
Posts: 8,768
Thanked 1,845 Times in 1,141 Posts
Default

Originally Posted by grbrown View Post
I'm not sure there were many models of TC88 that had a 103" engine. The TC96 model range has more models with a 103", but your trans won't bolt up to them, so that isn't going to work. In addition, Beagle's suggestion above will bring you many benefits over a stock 103", even if you have a slightly smaller capacity.

We have engine builders in here who you can contact for expert help, to actually perform mods and supply new parts. Pop into the Tech Engine section and consider contacting Scott at Hillside Cycle. Tell him you're a member of HDF! A proven aftermarket package should really light up your bike!
A later Twin Cam will bolt to the 2006 Dyna trans GR, that was the year the Dyna got the hydraulic tensioners and 6 speed transmission with the pass thru oil passages. Still a 4" stroke on the engine though.

 
Reply With Quote
The Following User Says Thank You to Nomadmax For This Useful Post:
grbrown (02-13-2018)
  #6  
Old 02-13-2018, 11:33 AM
djl's Avatar
djl
djl is offline
Ultimate HDF Member
Join Date: Jun 2006
Location: san antonio
Posts: 8,493
Thanks: 0
Thanked 325 Times in 301 Posts
Default

Your ECM will work. IIRC, '06 and up cable operated T/Bs are 46mm, so your T/B may very well be the same as the donor motor but not sure about the T/B size from a 103" motor but if larger, you could run it. FBW T/Bs are larger but no good in your situation. Any Dyna or Touring motor from an '07 up Twin Cam will swap out. You can wire the ACRs to the ECM but may require a new harness; not sure about that but you could also wire to the starter as you suggested.

I think I would plan and build a 98" motor. I have seen some strong 98" motors making near 120TQ/115HP; just need the right components and a good tune.
 
Reply With Quote
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
abez
Engine Mechanical Topics
18
02-19-2018 08:33 PM
pkachoochoo
Softail Models
15
06-28-2017 10:00 PM
Max Headflow
The Dyno Room
0
06-23-2017 12:07 AM
Red023783
Frame/Suspension/Front End/Brakes
0
03-03-2017 05:48 AM
Rollcage
Dyna Glide Models
4
06-17-2016 11:04 AM


Thread Tools
Search this Thread
Quick Reply: 06 FXD TC88 to 103..help


Featured Sponsors
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: