2014-2023 Touring Models This Section Is For Rushmore/2014-2023 Touring Models
Sponsored by:
Sponsored by:

Power Source

Thread Tools
 
Search this Thread
 
  #1  
Old 01-23-2018, 10:55 AM
BigDogIdaho's Avatar
BigDogIdaho
BigDogIdaho is offline
Grand HDF Member
Thread Starter
Join Date: Oct 2012
Location: Boise, ID
Posts: 3,728
Received 187 Likes on 145 Posts
Default Power Source

Hey all,

I've got a 17 Road King with heated grips (from HD) and I was wondering if there is a power source in the neck/headlight area that is easy to get to? Wanting to charge a phone or GPS. Shouldn't need both at once.

TIA
 
  #2  
Old 01-23-2018, 11:20 AM
rwven's Avatar
rwven
rwven is offline
Road Master
Join Date: Sep 2014
Location: North East, MD
Posts: 1,189
Received 232 Likes on 177 Posts
  #3  
Old 01-23-2018, 11:33 AM
hbsoldier3's Avatar
hbsoldier3
hbsoldier3 is offline
Elite HDF Member

Join Date: May 2007
Location: Bear Flag, lower end
Posts: 4,452
Received 796 Likes on 623 Posts
Default

On my RK, I ran one of these off the battery charging cable, then ran a USB cable up under the tank to the bars. It was an easy installation, mounted the unit with velco against frame above the starter. That way I would just disconnect the unit and plug my battery tender in while the bike is in the garage.

Amazon Amazon
 

Last edited by hbsoldier3; 01-23-2018 at 11:34 AM.
The following users liked this post:
cycle7447 (01-23-2018)
  #4  
Old 01-23-2018, 05:56 PM
BigDogIdaho's Avatar
BigDogIdaho
BigDogIdaho is offline
Grand HDF Member
Thread Starter
Join Date: Oct 2012
Location: Boise, ID
Posts: 3,728
Received 187 Likes on 145 Posts
Default

Originally Posted by hbsoldier3
On my RK, I ran one of these off the battery charging cable, then ran a USB cable up under the tank to the bars. It was an easy installation, mounted the unit with velco against frame above the starter. That way I would just disconnect the unit and plug my battery tender in while the bike is in the garage.

https://www.amazon.com/Battery-Tende.../dp/B00DJ5KEF4

Was it very difficult to get under the tank?
 
  #5  
Old 01-23-2018, 07:42 PM
hbsoldier3's Avatar
hbsoldier3
hbsoldier3 is offline
Elite HDF Member

Join Date: May 2007
Location: Bear Flag, lower end
Posts: 4,452
Received 796 Likes on 623 Posts
Default

Originally Posted by BigDogIdaho
Was it very difficult to get under the tank?
No, I just unscrewed the rear console screw, and slid the wire under the rubber molding on the left side of the tank.
 

Last edited by hbsoldier3; 01-23-2018 at 07:43 PM.
  #6  
Old 01-23-2018, 08:22 PM
BigDogIdaho's Avatar
BigDogIdaho
BigDogIdaho is offline
Grand HDF Member
Thread Starter
Join Date: Oct 2012
Location: Boise, ID
Posts: 3,728
Received 187 Likes on 145 Posts
Default

Originally Posted by hbsoldier3
No, I just unscrewed the rear console screw, and slid the wire under the rubber molding on the left side of the tank.

So didn't really have to mess with the tank?
 
  #7  
Old 01-23-2018, 08:26 PM
hbsoldier3's Avatar
hbsoldier3
hbsoldier3 is offline
Elite HDF Member

Join Date: May 2007
Location: Bear Flag, lower end
Posts: 4,452
Received 796 Likes on 623 Posts
Default

Originally Posted by BigDogIdaho
So didn't really have to mess with the tank?
No not at all, took maybe 5 minutes to route the cable all the way up to the left hand grip area.
 
The following users liked this post:
BigDogIdaho (01-24-2018)
  #8  
Old 01-24-2018, 04:42 AM
Dsm Limited's Avatar
Dsm Limited
Dsm Limited is offline
Moderator
Join Date: Sep 2014
Location: Des moines IA
Posts: 7,421
Received 8,154 Likes on 2,935 Posts
Default

Removing a gas tank is a simple procedure. The fuel line is a quick disconnect. Pull the collar back and slip apart. When disconnected it has a check valve, so no leaks. It only dribbles a couple drops while removing. Easy, peasy
 
The following users liked this post:
BigDogIdaho (01-24-2018)
  #9  
Old 01-24-2018, 08:11 AM
BigDogIdaho's Avatar
BigDogIdaho
BigDogIdaho is offline
Grand HDF Member
Thread Starter
Join Date: Oct 2012
Location: Boise, ID
Posts: 3,728
Received 187 Likes on 145 Posts
Default

Probably the best looking option!
 
  #10  
Old 01-24-2018, 08:13 AM
BigDogIdaho's Avatar
BigDogIdaho
BigDogIdaho is offline
Grand HDF Member
Thread Starter
Join Date: Oct 2012
Location: Boise, ID
Posts: 3,728
Received 187 Likes on 145 Posts
Default

Originally Posted by Dsm Limited
Removing a gas tank is a simple procedure. The fuel line is a quick disconnect. Pull the collar back and slip apart. When disconnected it has a check valve, so no leaks. It only dribbles a couple drops while removing. Easy, peasy
I've never messed with tanks on either of the Harleys I've owned. Heard it was easy, but didn't realize it was quite that easy.
 


Quick Reply: Power Source



All times are GMT -5. The time now is 07:02 AM.