What did you do to Your Softail Today?
#6581
#6582
#6583
#6584
Reach Seat??
Took it out for a ride with the new pipes and intake, decided i need a seat that moves me forward an inch or three.
Looked at Danny gray, but dont see an option for reduced reach so i will call them on monday.
Any other seat suggestions. I only ride solo so the back seat is of no concern
Looked at Danny gray, but dont see an option for reduced reach so i will call them on monday.
Any other seat suggestions. I only ride solo so the back seat is of no concern
Make sure the handlebars are positioned where they are most confortable. The guys who install them at the deal;ership must all be 6' or taller.
#6585
Took it out for a ride with the new pipes and intake, decided i need a seat that moves me forward an inch or three.
Looked at Danny gray, but dont see an option for reduced reach so i will call them on monday.
Any other seat suggestions. I only ride solo so the back seat is of no concern
Looked at Danny gray, but dont see an option for reduced reach so i will call them on monday.
Any other seat suggestions. I only ride solo so the back seat is of no concern
I had the same situation on a Road King and put one on it. Maybe not the most comfortable seat for some folks but it worked for me.
#6586
#6587
Join Date: Nov 2010
Location: Red Banks, Mississippi
Posts: 17,456
Received 3,931 Likes
on
2,288 Posts
Went for a nice 150 mile putt yesterday...about half country roads and half interstate.
It was nice after a long cold winter to ride in 75* temps!
Saw this Copper highlighted bagger-
Got home and decided to check out my floorboards.
I like to scrape, even when I don't need to...making sparks is just fun.
Over time I have effectively increased my lean angle a few degrees.
BUT, I'm about at the limit. While I don't mind scraping the boards, because they move...I'm at the point where when I lean enough to scrape the boards, it's also beginning to scrape other, non-moving parts.
So, I'll either have to stop scraping, get new boards, or, what I'll probably do is get some Titanium feelers to put on the bottom of the floorboards.
These will let me touch down, not hit any hard parts I don't want to, and make lots of sparks.
It was nice after a long cold winter to ride in 75* temps!
Saw this Copper highlighted bagger-
Got home and decided to check out my floorboards.
I like to scrape, even when I don't need to...making sparks is just fun.
Over time I have effectively increased my lean angle a few degrees.
BUT, I'm about at the limit. While I don't mind scraping the boards, because they move...I'm at the point where when I lean enough to scrape the boards, it's also beginning to scrape other, non-moving parts.
So, I'll either have to stop scraping, get new boards, or, what I'll probably do is get some Titanium feelers to put on the bottom of the floorboards.
These will let me touch down, not hit any hard parts I don't want to, and make lots of sparks.
#6588
Oil tank
Well that damn hose from the oil tank (drain line) has been removed, replaced with a much stronger 3/4 hose and brass 90 degree coupler that works like a charm. That cheap hose that is stock is thin and useless, sorry i should have taken some pictures. Going to make a few more and sell them for $25.
#6589
Wellll... custom fitted a led into the bucket with brass fin grill. Brass air cleaner plate and floor boards. Brass head bolt covers and capped all bolts in black. Brass hand grips and derby cover as well as shifter peg and timing cover. Brass axle covers and pivot. Leatherworks saddlebag and basanni firesweeps with tune.
#6590
Went for a nice 150 mile putt yesterday...about half country roads and half interstate.
It was nice after a long cold winter to ride in 75* temps!
Got home and decided to check out my floorboards.
I like to scrape, even when I don't need to...making sparks is just fun.
Over time I have effectively increased my lean angle a few degrees.
BUT, I'm about at the limit. While I don't mind scraping the boards, because they move...I'm at the point where when I lean enough to scrape the boards, it's also beginning to scrape other, non-moving parts.
So, I'll either have to stop scraping, get new boards, or, what I'll probably do is get some Titanium feelers to put on the bottom of the floorboards.
These will let me touch down, not hit any hard parts I don't want to, and make lots of sparks.
It was nice after a long cold winter to ride in 75* temps!
Got home and decided to check out my floorboards.
I like to scrape, even when I don't need to...making sparks is just fun.
Over time I have effectively increased my lean angle a few degrees.
BUT, I'm about at the limit. While I don't mind scraping the boards, because they move...I'm at the point where when I lean enough to scrape the boards, it's also beginning to scrape other, non-moving parts.
So, I'll either have to stop scraping, get new boards, or, what I'll probably do is get some Titanium feelers to put on the bottom of the floorboards.
These will let me touch down, not hit any hard parts I don't want to, and make lots of sparks.