Originally Posted by JimmyL
(Post 15998814)
I just finished installing my Hammer 1250 jugs, pistons, carb jets and Dyna ignition. Today will be my first ride - I did the first heat cycles yesterday. Throttle cable fell apart when I was disassembling stuff. That replacement took me a long time. But I'm stoked now to take her out for a short run.
Had you previously swapped out the clutch ? just wondering... thanks, T. |
Originally Posted by WKNDS
(Post 15990484)
(prior 883->1200 primary gear/chain swap, Energy One/Muller power
clutch swap) Adusted the primary chain, adjusted the clutch pull. (Edit: forgot to mention that I replaced the bolts with AlloyBoltz, and to the horror of some, using ATF type 'F' in the tranny) A big shout out to Steve Cole at TTS for updating the Mastertune Sportster Cals! I spent some time coping timing/AFR tables to the new MT9 base so it'll be ready for some VTune3 recordings after the inital fire-up/break-in cycles. T. |
Originally Posted by cvaria
(Post 15998970)
Wait, when did you reassemble the top end? I've been trying to keep tabs on what you were doing to see how and what you did.
I haven't - yet... Don't need to for clutch/chain tension. I just have the jugs held down with a couple pcv unions (see HP website) while I move the drivetrain for cold checks... T. |
Originally Posted by cvaria
(Post 15998970)
Wait, when did you reassemble the top end? I've been trying to keep tabs on what you were doing to see how and what you did.
Originally Posted by WKNDS
(Post 15999009)
I haven't - yet... Don't need to for clutch/chain tension. I just have
the jugs held down with a couple pcv unions (see HP website) while I move the drivetrain for cold checks... |
Fixed the rear turn signal wires and added some LED lights while I was at it
https://cimg1.ibsrv.net/gimg/www.hdf...b816635147.jpg |
Originally Posted by WKNDS
(Post 15999009)
I haven't - yet... Don't need to for clutch/chain tension. I just have
the jugs held down with a couple pcv unions (see HP website) while I move the drivetrain for cold checks... T.
Originally Posted by multihdrdr
(Post 15999022)
Phew...at ease C, at ease :)
|
1 Attachment(s)
New shifter. Needs a small position adjustment but it feels great; I like it a lot.
|
installed my mirror extensions. Didnt work out as well as I hopes, as using the 'upside down' for the inverted mirrors ends up interfering with the clutch lever - unless you point it about 45* forward so the bolt/nut is in front of the clutch lever. throttle side worked out pretty well. Definitely moves is farther out though, even an inch is extremely noticeable.
|
Originally Posted by samhallnc
(Post 15999898)
New shifter. Needs a small position adjustment but it feels great; I like it a lot.
|
Fedex arrived and I did this:
https://cimg6.ibsrv.net/gimg/www.hdf...9a8b741bac.jpg FuelMoto Delivered! I started it after installing the custom map, and I dunno, but I think it Sounds better than the PC-V I have. Plus the data and being able to use the narrow band at least O2 make me feel better. Now Im waiting for UPS, and my hammer impact AC :D Also rerouted the wires from the handle bars so they slip behind the headlight again. I wish someone had said a year ago, the tank comes off with 2 bolts, and 3 plugs. Cause man its So easy. wiring my USB would have been so much easier. all anyone said was 'just take the tank off'. haha. Well yea, Just take the tank off, its Super Simple! |
All times are GMT -5. The time now is 08:19 AM. |
© 2024 MH Sub I, LLC dba Internet Brands