Harley Davidson Forums
0 2019/10/02 20:14:42
This is my final opening, I think I used a 9/32" drill.
This is my final opening, I think I used a 9/32" drill.
0 2019/10/05 18:20:00
This is the core. These holes are about 50% larger than stock, and I opened them further to how they look in the next pic.
This is the core. These holes are about 50% larger than stock, and I opened them further to how they look in the next pic.
0 2019/10/05 18:20:06
This is what the housing looks like with the core removed. Seriously I believe these with the core out and Thunder Torque inserts would sound just as good as the Cobras. I might just try that before its all over.
This is what the housing looks like with the core removed. Seriously I believe these with the core out and Thunder Torque inserts would sound just as good as the Cobras. I might just try that before its all over.
0 2019/10/05 18:20:12
0 2019/10/05 18:26:26
0 2019/10/05 18:26:32
0 2019/10/05 18:29:22
0 2019/10/19 19:23:19
0 2019/10/19 19:23:30
0 2019/10/19 19:23:35
0 2019/10/22 13:40:50
0 2019/10/25 19:17:11
0 2019/10/25 19:19:06
0 2019/10/25 19:24:56
0 2019/10/25 19:31:06
0 2019/10/25 19:32:20
0 2019/10/25 19:35:17
0 2019/10/26 17:47:37
0 2019/10/26 17:47:43
0 2019/10/26 17:49:52
0 2019/10/26 17:49:57
Look real close to the left of the rear cylinder to see the copper and hose.
Look real close to the left of the rear cylinder to see the copper and hose.
0 2019/10/26 17:52:02
This is from the left side, and you have to look close to see the filter. The outlet of the filter runs down behind the crankcase beside brake line, and is zip tied to the brake line.
This is from the left side, and you have to look close to see the filter. The outlet of the filter runs down behind the crankcase beside brake line, and is zip tied to the brake line.
0 2019/10/26 17:52:06
0 2019/10/26 17:52:10
0 2019/10/28 11:48:16
Same bike diff angle and stock pipes.
Same bike diff angle and stock pipes.
0 2019/11/01 16:57:01
On tour
On tour
0 2019/11/01 16:57:40
0 2019/11/05 23:07:16
0 2019/11/05 23:08:21
0 2019/11/07 18:01:49
Just arrived. My wife took the pic.
Just arrived. My wife took the pic.
0 2019/11/09 16:36:38
Getting ready to head out. Mine is down by the suburban.
Getting ready to head out. Mine is down by the suburban.
0 2019/11/09 16:36:57
0 2020/01/02 13:47:36
Almost positive that a paper clip is supposed to release the terminal but cannot get it to work.
Almost positive that a paper clip is supposed to release the terminal but cannot get it to work.
0 2020/01/04 15:57:02
0 2020/01/04 19:30:19
This is just the wires soldered in place with heat shrink protection. The bare wires will have bullet connectors crimped on so they can quick connect from the wires leading to each bag. This end of the wire will be the female end, so if disconnected, the wires cannot short against each other inside the tail light housing.
This is just the wires soldered in place with heat shrink protection. The bare wires will have bullet connectors crimped on so they can quick connect from the wires leading to each bag. This end of the wire will be the female end, so if disconnected, the wires cannot short against each other inside the tail light housing.
0 2020/01/05 18:36:11
This is the strip light mounted to the bracket. This is the back side. I plan on blackening the edges of the angle to make it less obvious. Maybe. The three wires are grnd, tail, and brake.
This is the strip light mounted to the bracket. This is the back side. I plan on blackening the edges of the angle to make it less obvious. Maybe. The three wires are grnd, tail, and brake.
0 2020/01/05 18:40:17
This is the front of it, notice the screws holding it in place. I drilled and tapped the angle for 6-62 screws. I think I will touch up the screw heads with some red paint to blend them in also.
This is the front of it, notice the screws holding it in place. I drilled and tapped the angle for 6-62 screws. I think I will touch up the screw heads with some red paint to blend them in also.
0 2020/01/05 18:40:18
This is approximately how they will look mounted. I will run screws through the bag and back them up on the inside with washers and nuts, all thread locked in place. The wires from these strips do not need to go inside the bags, but will be encased in black conduit, and zip tied to the bag frame, to keep it away from moving parts. If I mount the amber turns, those WILL have to go through the bag, unfortunately. All wiring will be quick connected at one of the holes on the sub frame.
This is approximately how they will look mounted. I will run screws through the bag and back them up on the inside with washers and nuts, all thread locked in place. The wires from these strips do not need to go inside the bags, but will be encased in black conduit, and zip tied to the bag frame, to keep it away from moving parts. If I mount the amber turns, those WILL have to go through the bag, unfortunately. All wiring will be quick connected at one of the holes on the sub frame.
0 2020/01/05 18:40:20
0 2020/01/06 08:50:56
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands