Bike won't start....cold weather!!
#1
Bike won't start....cold weather!!
I have a 1988 Sportster. Its a stage 2.5 conversion and I have put 2000 trouble free miles on it in the last few months. It has always had a weird issue regarding starting. When I hit the startbutton depending on where the compression stroke is it will either turn over like a normal bike and start or.. it will just click and after a second it will suddenly start. Its similar to the other high performance high compression bikes I have heard. I took it to the dealer and they installed a new battery and the tech who worked on it told me its normal for a tricked out motor like mine. He has one too and it does the same thing. I have yet to have a problem starting it until this morning. Keep in mind.. I ALWAYS have the battery on a tender. The charging system on my bike works perfectly. I was all checked at the dealer and by me.
This morning..the temp was 36 degrees. My bike is in an unheated detached garage so its pretty cold in there. I haven't ridden the bike for 6 days. When I tried to start it this morning it initially turned over fine but it didn't start. After a few tries it just started clicking. I usually just have to hold the start button in for a second and it will fire up. This morning, it didn't. The starter cable was hot too after holding the start button in several times. I could smell the insulation on it cooking a little. My headlight is super bright btw.
I was thinking that I should replace my stock starter with one of the 1.4K or higher starters. Some guys told me that it won't help, others said it will. Is this normal for an old Sportster to have issues when its cold. I am looking forward to riding right up until it snows but if I can't get the bike started I guess I won't be doing much riding anymore.
Any suggestions are greatly appreciated.
This morning..the temp was 36 degrees. My bike is in an unheated detached garage so its pretty cold in there. I haven't ridden the bike for 6 days. When I tried to start it this morning it initially turned over fine but it didn't start. After a few tries it just started clicking. I usually just have to hold the start button in for a second and it will fire up. This morning, it didn't. The starter cable was hot too after holding the start button in several times. I could smell the insulation on it cooking a little. My headlight is super bright btw.
I was thinking that I should replace my stock starter with one of the 1.4K or higher starters. Some guys told me that it won't help, others said it will. Is this normal for an old Sportster to have issues when its cold. I am looking forward to riding right up until it snows but if I can't get the bike started I guess I won't be doing much riding anymore.
Any suggestions are greatly appreciated.
#2
#5
RE: Bike won't start....cold weather!!
Check the battery, make sure it has a good charge, I know you said you have a "tender" on it, just need to eliminate things. Next, check to see if you are getting a spark, pull a plug and lay it on the head with the plug wire on it and hit the starter.I know this sounds stupid, but, is the gas on? Don't even ask how I thought of that question.
#6
RE: Bike won't start....cold weather!!
Put your volt meter across the cables and try cranking it. That is, put one lead on one end of the cable and one lead on the other end of the cable and have the meter set on the volts scale. 20V range would be a good starting point, but you may need to go to a lower range depending on the meter. If you see a significant voltage across the cable when you crank it, then your cable is defective, regardless of it it is new or not. Other possibile issues you could be having are the starter solenoid (do the same test across it), too much compression for your starter motor to handle, weak starter motor or oil too thick. Are you running a full synthetic? Might help out with your cold starting.
Our '87 883 has no issues starting in the cold.
Our '87 883 has no issues starting in the cold.
#7
Join Date: May 2005
Location: A barrier island in NJ
Posts: 3,146
Likes: 0
Received 48 Likes
on
37 Posts
RE: Bike won't start....cold weather!!
If your cable is getting hot, the ohms have taken over. The resistanceis most likely tobe caused by loose, dirty or corroded cable ends. I know you say they are new cables but I would still double check to make sure that ALL 4 points of contact are clean (physically and chemically). Twice a year I dismantle my cables now, clean the ends with a wire brush and sandpaper, do the same on all 4 points where they connect, and then apply dilectric grease to all four connection points and the cable ends. This lack of good contact problem caught me off guard once, but will not do it a second time!
Trending Topics
#8
RE: Bike won't start....cold weather!!
ORIGINAL: Dr.Hess
Put your volt meter across the cables and try cranking it. That is, put one lead on one end of the cable and one lead on the other end of the cable and have the meter set on the volts scale. 20V range would be a good starting point, but you may need to go to a lower range depending on the meter. If you see a significant voltage across the cable when you crank it, then your cable is defective, regardless of it it is new or not. Other possibile issues you could be having are the starter solenoid (do the same test across it), too much compression for your starter motor to handle, weak starter motor or oil too thick. Are you running a full synthetic? Might help out with your cold starting.
Our '87 883 has no issues starting in the cold.
Put your volt meter across the cables and try cranking it. That is, put one lead on one end of the cable and one lead on the other end of the cable and have the meter set on the volts scale. 20V range would be a good starting point, but you may need to go to a lower range depending on the meter. If you see a significant voltage across the cable when you crank it, then your cable is defective, regardless of it it is new or not. Other possibile issues you could be having are the starter solenoid (do the same test across it), too much compression for your starter motor to handle, weak starter motor or oil too thick. Are you running a full synthetic? Might help out with your cold starting.
Our '87 883 has no issues starting in the cold.
I spoke to Bob Johnson though and he told me that I didn't need a high torque starter. It has the stock 1988 starter for an 883 (the bike started its life in 1988 as an 883 Hugger). It is now a 88+hp 1200 that had $5000.00 worth of work (between parts and labor)done to the motor alone.
When you are talking about the cable.. do you mean the cable that goes from the positive terminal on the battery to the starter?
#9
RE: Bike won't start....cold weather!!
ORIGINAL: Thumper26
If your cable is getting hot, the ohms have taken over. The resistanceis most likely tobe caused by loose, dirty or corroded cable ends. I know you say they are new cables but I would still double check to make sure that ALL 4 points of contact are clean (physically and chemically). Twice a year I dismantle my cables now, clean the ends with a wire brush and sandpaper, do the same on all 4 points where they connect, and then apply dilectric grease to all four connection points and the cable ends. This lack of good contact problem caught me off guard once, but will not do it a second time!
If your cable is getting hot, the ohms have taken over. The resistanceis most likely tobe caused by loose, dirty or corroded cable ends. I know you say they are new cables but I would still double check to make sure that ALL 4 points of contact are clean (physically and chemically). Twice a year I dismantle my cables now, clean the ends with a wire brush and sandpaper, do the same on all 4 points where they connect, and then apply dilectric grease to all four connection points and the cable ends. This lack of good contact problem caught me off guard once, but will not do it a second time!
#10