Originally Posted by rocknrod (Post 8209225)

What is the little plug already in front of the HK radio (lower right corner)?

Originally Posted by Retrax (Post 8204909)

You can send your radio into iron cross. I think they can install a headphone out jack on it. You could then use a y splitter to have two 1/8 jacks out and use an inline volume control to adjust independent volume for you and a passenger.
www.ironcrossaudio.com...

Originally Posted by Wildman4x4nut (Post 8209304)

AUx input for your Ipod or other MP3 player.

Originally Posted by Texas Fat Boy (Post 8210017)

The simpliest way I have found is (this is simplar than I am making it sound)

Basicly I tied into where the speaker wires plug into the speakers
I wanted everything to plug in and unplug so:

I made a Y connector (two female and one male ends) with extra wire speaker wire and some spade connectors.

Using the Y connector: Plug the stock speaker wire into the male end, then one female end into the fairing speaker
and the other end into a speaker wire that I had gotten from radio shack (that was speaker wire that had a male RCA jack end - that's all they had) you will need to add a spade connector to one end.

(or just soder the headphone wires to the stock wires)

http://ecx.images-amazon.com/images/...500_AA150_.jpg

I had a double RCA female coupler

http://lh4.googleusercontent.com/pub..._2VtR5t6rJiXtw

This plugs into an iPod 3.5 adapter, like a Pyle (PLIPG1) iPod 3.5mm Stereo to RCA Adaptor
The white wire in the picture is unused

http://lh4.googleusercontent.com/pub...Rl_N5ECdtnPmuQ

I did not want to drill a hole anywhere and this one sticks on with body moulding tape.
When you order one make sure it's black, a lot of them are white.

Once you get settled on what and where you want it and want to drill a hole, this is a black water proof one:
http://www.crutchfield.com/S-g0FhPwM...-IC-3-5PM.html

http://a248.e.akamai.net/pix.crutchf...3iC35PM-fp.jpg

I originaly mounted it on the fairing but the headphone wire kind of dances around in the wind, so the second time I ran some wires under the gas tank and ran the wires back to the battery area and mounted the iPod headphone jack to my heat shield. Now I don't see the wire dancing above the gas tank.

I guess I need to take some real pictures and do a write up. lol

With this setup I use some Skull Daddy ear Buds and I can hear perfectly. Even soft pop/rock.
I have the AVC on and never get above the second bar on the volume.
Way better than any speaker/amp setup and I've been the 6 1/2" speakers and 360 watt setup route. I still couldn't hear it clear enough at 70 into a head wind with the big amp and big speakers.

This should all cost less than $30

Originally Posted by jims79flh (Post 8210409)

Texas Fat Boy,
Did you do that mode to just one side of your speakers (mono) or did you use both sides (stereo)?? Are the fairing speakers still on while you listen to your headphones? Thanks for the help.

Originally Posted by jims79flh (Post 8210409)

Texas Fat Boy,
Did you do that mode to just one side of your speakers (mono) or did you use both sides (stereo)?? Are the fairing speakers still on while you listen to your headphones? Thanks for the help.

Originally Posted by rocknrod (Post 8209645)

I think I will send mine in. Move that aux jack to the back and have a headphone jack in the front. :icon_clapclap:
Also have them change the color of the LED to amber, like the gauges.

Originally Posted by hwyhound (Post 8211685)

Just Got mine back from Iron Cross yesterday and I’m VERY pleased with the results. Both the auxiliary and headphone exit the rear of the radio. The headphone cable is 60” long, enough to run to the rear of the tank. There is also a switch included to toggle between your speakers and the headphones.

Originally Posted by drspencer (Post 8211704)

This is exactly what I want to do. What does their toggle switch look like? Could you post a pic?
Thanks