Fuel Moto ventilator
#52
I think that’s the only one in existence. I have a couple extras in case Amazon stops selling them... Note that the barbs are a little small for 3/8” and too big for 1/4” fuel hose. I used 1/4” and heated it up a bit to fit it over easier.
#53
Mine arrived last week. Modified to vent externally, installed it, sat on the bike and immediately removed it and put the Heavy Breather back on. The FuelMoto kit sticks out too far and my legs apparently are too long so they hit. Won’t work for me. Going on the classifieds later tomorrow probably. Disappointed...
Bought a new HD cover and insert as well. $ down the drain...
Bought a new HD cover and insert as well. $ down the drain...
Have you considered getting some floorboard extenders? I put these on my old 2010 Street Glide, and they were awesome. They only move the boards 3/4" outward (to the left and right, respectively), but what a difference in comfort, and general room to move your feet around. On the right side, it helps keep your heel away from the exhaust pipe, and might just give you room to clear your knee/thigh from the air cleaner. On the left side, it gives you a ton of room away from your shifter(s). You might want to give it a try.
P.S. Never scraped a floorboard with these either, and I ride pretty aggressive.
https://www.thepropad.com/fb-ext9-fl...nt-harley-fls/
The following users liked this post:
Godinaz (07-28-2019)
#54
Mchad,
Have you considered getting some floorboard extenders? I put these on my old 2010 Street Glide, and they were awesome. They only move the boards 3/4" outward (to the left and right, respectively), but what a difference in comfort, and general room to move your feet around. On the right side, it helps keep your heel away from the exhaust pipe, and might just give you room to clear your knee/thigh from the air cleaner. On the left side, it gives you a ton of room away from your shifter(s). You might want to give it a try.
P.S. Never scraped a floorboard with these either, and I ride pretty aggressive.
https://www.thepropad.com/fb-ext9-fl...nt-harley-fls/
Have you considered getting some floorboard extenders? I put these on my old 2010 Street Glide, and they were awesome. They only move the boards 3/4" outward (to the left and right, respectively), but what a difference in comfort, and general room to move your feet around. On the right side, it helps keep your heel away from the exhaust pipe, and might just give you room to clear your knee/thigh from the air cleaner. On the left side, it gives you a ton of room away from your shifter(s). You might want to give it a try.
P.S. Never scraped a floorboard with these either, and I ride pretty aggressive.
https://www.thepropad.com/fb-ext9-fl...nt-harley-fls/
Thanks though!
#55
I went to Jamie at Fuelmoto on Tuesday this week to have my bike tuned by him. He ran it with the HD ventilator air cleaner i had on the bike and then showed me what it was without the HD brand ventilator. There was an exactly 10 HP and 10 TQ difference without the HD brand. We then put his brand of the ventilator on and did in fact gain the 10 HP and 10 TQ. Came out after tune to what have now at 129.45 HP and 129.40 TQ. Very happy with the final results. Big thanks go out to Jamie for taking the time to go the extra steps to help me on my bike’s tune.
The following 3 users liked this post by ghostrunner:
#56
Available?
Do you still have this, and want to sell?
Mine arrived last week. Modified to vent externally, installed it, sat on the bike and immediately removed it and put the Heavy Breather back on. The FuelMoto kit sticks out too far and my legs apparently are too long so they hit. Won’t work for me. Going on the classifieds later tomorrow probably. Disappointed...
Bought a new HD cover and insert as well. $ down the drain...
Bought a new HD cover and insert as well. $ down the drain...
Thread
Thread Starter
Forum
Replies
Last Post
FenderGuy53
Touring Models
24
04-29-2013 10:17 AM