Harley Davidson Forums
0 2020/03/22 17:21:30
0 2020/03/25 06:56:33
0 2020/03/25 06:57:34
0 2020/03/27 17:52:00
0 2020/03/27 17:53:00
0 2020/03/27 17:57:03
The tape seen at the lower right in the case once held a small screwdriver that was needed to frequently tighten the screws that loosened from the recoil. Ruger eventually sent out Nylok screws to solve that problem!
The tape seen at the lower right in the case once held a small screwdriver that was needed to frequently tighten the screws that loosened from the recoil. Ruger eventually sent out Nylok screws to solve that problem!
0 2020/03/29 09:02:22
0 2020/03/29 09:06:30
0 2020/03/30 13:00:14
0 2020/03/30 13:01:50
0 2020/04/01 07:27:44
0 2020/04/02 18:01:42
0 2020/04/02 18:02:20
0 2020/04/02 18:04:40
0 2020/04/02 18:05:25
0 2020/04/02 18:06:17
0 2020/04/11 18:03:58
0 2020/04/11 18:06:13
0 2020/04/11 18:09:59
0 2020/04/11 18:11:58
0 2020/04/11 18:15:47
0 2020/04/11 18:16:54
0 2020/04/11 18:18:21
0 2020/04/11 19:11:30
0 2020/04/11 19:12:36
0 2020/04/11 19:14:02
0 2020/04/11 19:15:08
0 2020/04/11 19:22:21
Winchester "Nutcracker" type reloading tool.
Winchester "Nutcracker" type reloading tool.
0 2020/04/13 16:05:07
Another Winchester tool.
Another Winchester tool.
0 2020/04/13 16:05:38
12 gauge primer tool.
12 gauge primer tool.
0 2020/04/13 16:06:08
12 gauge primer tool.
12 gauge primer tool.
0 2020/04/13 16:06:37
Two Winchester tools for .32-20 WCF; notice the difference in the primer/sizer/ pieces, even tho they are the same caliber.
Two Winchester tools for .32-20 WCF; notice the difference in the primer/sizer/ pieces, even tho they are the same caliber.
0 2020/04/13 16:07:09
So, any of y'all old-timers recognize this? It's a home-made bullet luber. There is a nail between the two shells that runs through the primer holes. A flat piece the diameter of the bullet is silver soldered to the end of the nail inside the top shell. Bullet wax is melted into a container and bullets placed into the wax. When the wax solidifies this tool is pushed down over a bullet, the bottom shell is pulled apart from the top which creates a vacuum and pulls the bullet from the wax.
So, any of y'all old-timers recognize this? It's a home-made bullet luber. There is a nail between the two shells that runs through the primer holes. A flat piece the diameter of the bullet is silver soldered to the end of the nail inside the top shell. Bullet wax is melted into a container and bullets placed into the wax. When the wax solidifies this tool is pushed down over a bullet, the bottom shell is pulled apart from the top which creates a vacuum and pulls the bullet from the wax.
0 2020/04/13 16:07:44
Grandad made this bullet cherry; it was used to make a bullet mold for .32-20 WCF.
Grandad made this bullet cherry; it was used to make a bullet mold for .32-20 WCF.
0 2020/04/13 16:08:11
Another of his home-made cherries; this one is about a .32 round ball.
Another of his home-made cherries; this one is about a .32 round ball.
0 2020/04/13 16:08:44
Sporterized 1896 Krag .30-40 Government
Sporterized 1896 Krag .30-40 Government
0 2020/04/19 20:41:42
1896 Krag .30-40 Government
1896 Krag .30-40 Government
0 2020/04/19 20:42:33
1896 Krag .30-40 Government
1896 Krag .30-40 Government
0 2020/04/19 20:43:10
1898 Krag .30-40 Government
1898 Krag .30-40 Government
0 2020/04/19 20:45:40
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands