Harley Davidson Forums
81 FXEF
81 FXEF
0 2017/01/07 09:00:24
Building a boring bar stand
Building a boring bar stand
0 2022/01/07 07:29:02
An afternoon of fab time
An afternoon of fab time
0 2022/02/13 17:23:17
Crank runout check
Crank runout check
0 2018/02/03 20:50:47
More hand crafted tools
More hand crafted tools
0 2019/03/24 08:13:57
Timken races....
Timken races....
0 2019/03/24 08:20:25
My FXDLS on the bench for high compression pistons , cams , 58mm throttle body , ported heads and up sized injectors
My FXDLS on the bench for high compression pistons , cams , 58mm throttle body , ported heads and up sized injectors
0 2018/02/03 20:54:30
Reverse engineered version of a Kent Moore Timken bearing race tool. When I worked at a dealership , at lunch time , I reverse engineered lots of expensive and hard to get Kent Moore service tools ....., made drawings , then went home and made my own . I even designed a few tools that haven't been concieved yet and created them from an idea . A good mechanic is a problem solver and can think outside the box.
Reverse engineered version of a Kent Moore Timken bearing race tool. When I worked at a dealership , at lunch time , I reverse engineered lots of expensive and hard to get Kent Moore service tools ....., made drawings , then went home and made my own . I even designed a few tools that haven't been concieved yet and created them from an idea . A good mechanic is a problem solver and can think outside the box.
0 2019/03/24 08:18:59
rubber on the floor , much better to stand / walk on
rubber on the floor , much better to stand / walk on
0 2021/01/26 05:25:10
Six months after buying my Sunnen hone , I'm just now starting to outfit it . Ebay has saved me thousands !!
Six months after buying my Sunnen hone , I'm just now starting to outfit it . Ebay has saved me thousands !!
0 2021/03/14 06:39:42
checking fit
checking fit
0 2018/02/03 20:50:03
Machinist stuff
Machinist stuff
0 2018/02/25 11:47:33
Plugged Piston cooling jets = engine failure
Plugged Piston cooling jets = engine failure
0 2021/04/25 11:15:55
Grinding the valve seats
Grinding the valve seats
0 2019/03/24 08:12:50
Installing the clip
Installing the clip
0 2019/03/24 08:17:23
my welders
my welders
0 2022/03/10 05:26:45
One of my old Nortons
One of my old Nortons
0 2020/09/12 18:19:57
My old F100 4x4 & the XR1000 I bought new
My old F100 4x4 & the XR1000 I bought new
0 2020/09/26 06:06:21
Custom Jeep cylinder head
Custom Jeep cylinder head
0 2017/12/16 08:40:56
98" Evo 4 3/4 " x 3 5/8"
98" Evo 4 3/4 " x 3 5/8"
0 2019/01/20 11:40:35
Bought some rubber for the floor , better than standing on cold hard concrete.
Bought some rubber for the floor , better than standing on cold hard concrete.
0 2021/01/26 05:23:13
Checking spring pressure at installed height
Checking spring pressure at installed height
0 2018/02/03 20:47:16
Multi angle valve seats
Multi angle valve seats
0 2018/02/03 20:47:41
Counter boring an early S&S cylinder to fit over shouldered studs , after all ..... the stud do go in with the shoulder / step down .....
Counter boring an early S&S cylinder to fit over shouldered studs , after all ..... the stud do go in with the shoulder / step down .....
0 2019/03/24 08:25:16
Making a valve seal driver for screamin eagle valve guide seals
Making a valve seal driver for screamin eagle valve guide seals
0 2019/03/24 08:26:48
Checking crankshaft end play
Checking crankshaft end play
0 2019/03/24 08:15:22
Installing the crank /Timken bearing
Installing the crank /Timken bearing
0 2019/03/24 08:21:09
Ported heads
Ported heads
0 2018/02/03 20:48:04
My 81 FXEF
My 81 FXEF
0 2017/01/07 08:59:39
It's winter , stayin warm and outa the weather
It's winter , stayin warm and outa the weather
0 2021/03/14 06:42:29
1984 Shovelhead build
1984 Shovelhead build
0 2019/03/24 08:18:16
S&S Stroker pistons- 4 3/4" stroke , evo cam/valvetrain conversion
S&S Stroker pistons- 4 3/4" stroke , evo cam/valvetrain conversion
0 2017/01/07 09:06:02
Keepin the older iron alive
Keepin the older iron alive
0 2019/03/24 08:32:49
seats installed , more work to do ....
seats installed , more work to do ....
0 2019/03/24 08:11:45
Jim's oil pump retaining ring tool
Jim's oil pump retaining ring tool
0 2019/03/24 08:16:32
Machining stuff
Machining stuff
0 2017/12/16 08:15:24
0 2018/02/03 20:51:13
Playing around with my mill on an old S&S cover
Playing around with my mill on an old S&S cover
3 2018/02/25 10:24:31
My old Vrod
My old Vrod
0 2019/01/20 12:53:14
Sometimes I buy tools ,sometimes I make tools , er , umm , I've made lots of tools
Sometimes I buy tools ,sometimes I make tools , er , umm , I've made lots of tools
0 2019/01/20 11:47:56
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands