Harley Davidson Forums
86k
86k
0 2026/01/28 09:57:47
Inner shows almost no wear
Inner shows almost no wear
0 2026/01/28 09:57:51
0 2026/01/28 09:57:58
The reciprocating assembly was smooth as silk. Rod play was excellent as well. I’ll get her shipped off soon.
The reciprocating assembly was smooth as silk. Rod play was excellent as well. I’ll get her shipped off soon.
0 2026/01/28 09:58:04
0 2026/01/28 09:58:08
0 2026/01/28 09:58:13
0 2026/01/28 09:58:19
0 2026/01/31 16:42:15
0 2026/01/31 16:42:20
0 2026/01/31 16:42:24
All packed. Pistons, rings, and hardware.
All packed. Pistons, rings, and hardware.
0 2026/01/31 16:44:30
0 2026/01/31 16:44:35
A bit of a pain to install but not horrible. I wound up removing a squaring the race up a few times.
A bit of a pain to install but not horrible. I wound up removing a squaring the race up a few times.
0 2026/01/31 16:44:40
0 2026/01/31 16:44:45
0 2026/01/31 16:44:50
Success
Success
0 2026/01/31 16:44:55
All good
All good
0 2026/01/31 16:44:59
Countershaft bearing
Countershaft bearing
0 2026/01/31 16:45:03
0 2026/01/31 16:45:07
Seated
Seated
0 2026/01/31 16:45:12
Had to improvise on a spacer. The OEM tool is too shallow to completely seat the MDG. It worked.
Had to improvise on a spacer. The OEM tool is too shallow to completely seat the MDG. It worked.
0 2026/01/31 16:45:19
0 2026/01/31 16:45:25
0 2026/01/31 16:45:29
0 2026/01/31 16:45:34
The pre installed spacer for the MDG left me with no runout at all so I had to swap the blue spacer out for the red in order to get proper clearance. Easy to do, remove o ring and spacer.
The pre installed spacer for the MDG left me with no runout at all so I had to swap the blue spacer out for the red in order to get proper clearance. Easy to do, remove o ring and spacer.
0 2026/01/31 16:45:38
0 2026/02/01 12:09:56
0 2026/02/01 12:10:01
0 2026/02/01 12:10:06
0 2026/02/01 12:10:11
0 2026/02/01 12:10:15
0 2026/02/01 12:10:20
0 2026/02/01 12:10:53
0 2026/02/01 12:11:35
Seals installed
Seals installed
0 2026/02/01 12:11:40
Lucky me, I had to clearance just a bit.
Lucky me, I had to clearance just a bit.
0 2026/02/01 12:12:31
0 2026/02/01 12:12:36
Then I had to clearance again. Be advised, if you choose this combination as well you will have to clearance for the one bolt head in the side door. The PM hydraulic clutch cover is not machined to be a bolt on. I didn’t notice until it started to leak after filling it up.
Then I had to clearance again. Be advised, if you choose this combination as well you will have to clearance for the one bolt head in the side door. The PM hydraulic clutch cover is not machined to be a bolt on. I didn’t notice until it started to leak after filling it up.
0 2026/02/01 12:13:54
0 2026/02/01 12:13:58
0 2026/02/01 12:14:03
0 2026/02/01 12:14:07
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands