Harley Davidson Forums
0 2020/05/07 05:16:53
0 2020/05/07 05:15:43
In with the new!
In with the new!
0 2020/05/04 05:24:13
Out with the old...
Out with the old...
0 2020/05/04 05:23:51
0 2020/04/06 15:15:15
0 2020/04/06 15:15:13
Solomon's Castle - January, 2019
Solomon's Castle - January, 2019
0 2020/01/20 06:17:20
Ready to roll...
Ready to roll...
0 2019/11/30 15:09:57
I used tape rather than tie-downs for low-profile wire-management.
I used tape rather than tie-downs for low-profile wire-management.
0 2019/11/30 15:05:54
Bolted into the pak.
Bolted into the pak.
0 2019/11/30 15:01:46
Trim-line runs straight-through the lower cover-screw hole.
Trim-line runs straight-through the lower cover-screw hole.
0 2019/11/30 15:01:32
Ready to mount!
Ready to mount!
0 2019/11/30 15:01:12
0 2019/10/19 15:51:07
0 2019/10/08 12:12:23
0 2019/10/08 12:12:07
0 2019/10/01 20:37:54
0 2019/10/01 20:36:25
0 2019/10/01 20:35:29
0 2019/09/26 11:11:53
0 2019/09/26 11:09:37
Side-by-side with and without harness installed...
Side-by-side with and without harness installed...
0 2019/09/26 11:05:01
0 2019/09/25 10:34:41
0 2019/09/22 18:31:18
0 2019/09/22 18:30:32
0 2019/09/20 15:44:09
Completed installation...
Completed installation...
0 2019/09/20 10:54:43
0 2019/09/20 10:54:26
Final fitting...
Final fitting...
0 2019/09/20 10:49:38
Starter hole...
Starter hole...
0 2019/09/20 10:49:30
Knock-out marked...
Knock-out marked...
0 2019/09/20 10:40:49
Template bolted in place on tour-pak...
Template bolted in place on tour-pak...
0 2019/09/20 10:40:39
0 2019/09/20 10:40:30
Planned notch. Notice the drill-marks on the base-plate - remnants of the previous install.
Planned notch. Notice the drill-marks on the base-plate - remnants of the previous install.
0 2019/09/17 11:18:26
Removed the base-plate and used the Dremel with a cutting wheel for rough cut, then grinding stone to smooth and shape. Quick file to deburr.
Removed the base-plate and used the Dremel with a cutting wheel for rough cut, then grinding stone to smooth and shape. Quick file to deburr.
0 2019/09/17 11:18:22
Finished view — and no more self-inflicted injury remorse.
Finished view — and no more self-inflicted injury remorse.
0 2019/09/17 06:25:33
Fine-tuning and finishing with barrel sander.
Fine-tuning and finishing with barrel sander.
0 2019/09/17 06:25:24
Initial cut-out with carbide cutting bit.
Initial cut-out with carbide cutting bit.
0 2019/09/17 06:25:15
0 2019/09/17 06:16:46
0 2019/09/16 20:01:36
0 2019/09/16 20:00:55
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands