Harley Davidson Forums
Checking clearanc efor the stoker flywheel ......
Checking clearanc efor the stoker flywheel ......
0 2025/01/17 07:44:36
Some port work ......
Some port work ......
0 2025/01/17 07:43:07
Mockup & prep ......
Mockup & prep ......
0 2025/01/17 07:42:02
I found that Harley still had the rh lower fork leg available so I added my second brake in August .
I found that Harley still had the rh lower fork leg available so I added my second brake in August .
0 2025/01/17 07:39:25
0 2022/01/24 08:39:28
0 2022/01/24 08:38:29
0 2022/01/24 08:37:00
0 2022/01/24 08:36:01
0 2022/01/24 08:33:02
0 2022/01/24 08:32:02
0 2021/03/14 06:36:22
0 2020/10/31 09:43:09
0 2020/10/25 18:13:53
0 2020/10/25 18:07:17
When she was a pup
When she was a pup
0 2020/08/23 07:39:52
0 2020/04/12 16:20:16
0 2019/03/26 18:51:40
The valve grinding machine came with the seat grinding kit and was too good of a deal to walk away from , I found that stuff at a used tool store , I just happened to be in the right place at the right time.
The valve grinding machine came with the seat grinding kit and was too good of a deal to walk away from , I found that stuff at a used tool store , I just happened to be in the right place at the right time.
0 2019/03/26 18:05:40
The whole home machine shop craze began innocently enough with the purchase of a small second hand drill press . I became frustrated with the state of things at work so I decided to buy my own cylinder head reconditioning equipment and it went on from there....
The whole home machine shop craze began innocently enough with the purchase of a small second hand drill press . I became frustrated with the state of things at work so I decided to buy my own cylinder head reconditioning equipment and it went on from there....
0 2019/03/26 18:02:53
One time , at work , I reverse engineered a Trock plate , went home and made my own so I could turn cylinder heads and machine nquench angles in the chamber for custom pistons. I used to reverse engineer alot of tools , still have a stack of drawings of stuff I haven't made yet.
One time , at work , I reverse engineered a Trock plate , went home and made my own so I could turn cylinder heads and machine nquench angles in the chamber for custom pistons. I used to reverse engineer alot of tools , still have a stack of drawings of stuff I haven't made yet.
0 2019/03/26 17:57:18
Some times I'd lighten flywheels and then true them .... on the same machine.
Some times I'd lighten flywheels and then true them .... on the same machine.
0 2019/03/26 17:56:22
Fly cut a Buell piston for clearance , I built and maintained a few Buell road race bikes for a laugh
Fly cut a Buell piston for clearance , I built and maintained a few Buell road race bikes for a laugh
0 2019/03/26 17:55:09
A buddy wanted to use an earlier 5 speed tapered mainshaft trans in a chopper and use a later starter . I set it up , fully assembled of course wwith the mainshaft verticle , on that 3 in 1 and bored the starter hole to the correct size.
A buddy wanted to use an earlier 5 speed tapered mainshaft trans in a chopper and use a later starter . I set it up , fully assembled of course wwith the mainshaft verticle , on that 3 in 1 and bored the starter hole to the correct size.
0 2019/03/26 17:52:20
0 2019/03/24 08:41:07
Sometimes I make tools , some times I buy them
Sometimes I make tools , some times I buy them
0 2019/03/24 08:05:05
Carbide reamer / bronze guides
Carbide reamer / bronze guides
0 2019/03/24 08:02:10
Guides and seats in ...
Guides and seats in ...
0 2019/03/24 08:00:36
This one gets new valve seats , guides , springs , valves , rocker arms n' shafts
This one gets new valve seats , guides , springs , valves , rocker arms n' shafts
0 2019/03/24 07:59:07
0 2019/03/24 07:56:28
Installing the crank/bearing to the left case
Installing the crank/bearing to the left case
0 2019/03/24 07:55:09
The Timken race tool .
The Timken race tool .
0 2019/03/24 07:54:03
This is a timken bearing mock up tool to establish endplay and select the correct spacer. Surprisingly , most Timken bearing sets are good to go out of the box but I check em anyways.
This is a timken bearing mock up tool to establish endplay and select the correct spacer. Surprisingly , most Timken bearing sets are good to go out of the box but I check em anyways.
0 2019/03/24 07:49:45
Years ago when I worked at the dealership, I reverse engineered a bunch of Kent Moore tools , here's the timken bearing race tool I made . It works on big twins or little twins .
Years ago when I worked at the dealership, I reverse engineered a bunch of Kent Moore tools , here's the timken bearing race tool I made . It works on big twins or little twins .
0 2019/03/24 07:48:52
A man needs stuff to do on the weekend , in the winter.
A man needs stuff to do on the weekend , in the winter.
0 2019/03/24 07:47:06
0 2019/03/23 14:17:49
0 2019/03/23 09:33:37
0 2019/02/07 16:55:20
this is at the installed hieght
this is at the installed hieght
0 2019/02/03 10:10:48
there's a couple of fork tube holders I made in this drawer
there's a couple of fork tube holders I made in this drawer
0 2019/01/19 12:53:48
I have one of the Jim's fork leg tools , it's cool butit needed a block of aluminum bolted on to grip it in the vise to hold forks both horizontally and vertically
I have one of the Jim's fork leg tools , it's cool butit needed a block of aluminum bolted on to grip it in the vise to hold forks both horizontally and vertically
0 2019/01/19 12:53:06
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands