Harley Davidson Forums
0 2018/09/12 16:33:37
0 2018/09/12 16:33:36
Here is a full side view I wanted to include with the previous post. The Wolo horn is very inconspectuous.
Here is a full side view I wanted to include with the previous post. The Wolo horn is very inconspectuous.
0 2018/09/03 10:35:50
1. Ran wires down to horn in flex tube. 2. Reinstalled Frame bolt with blue Locktite. 3. Top of horn was plain metal where I removed the logo sticker. Painted it Gloss black with Krylon Automotive paint.
1. Ran wires down to horn in flex tube. 2. Reinstalled Frame bolt with blue Locktite. 3. Top of horn was plain metal where I removed the logo sticker. Painted it Gloss black with Krylon Automotive paint.
0 2018/09/03 09:48:02
1. Relay under seat tucked down under side rail just above where horn is installed below. 2. Ran the two yellow wires from stock horn to relay as required in the wiring diagram from Wolo. Ran them in a black flex tube under the gas tank.
1. Relay under seat tucked down under side rail just above where horn is installed below. 2. Ran the two yellow wires from stock horn to relay as required in the wiring diagram from Wolo. Ran them in a black flex tube under the gas tank.
0 2018/09/03 09:40:50
Soldered the red wire to the main battery cable just behind the main fuse which is located under the left side cover. This is the power to the relay located under my seat.
Soldered the red wire to the main battery cable just behind the main fuse which is located under the left side cover. This is the power to the relay located under my seat.
0 2018/09/03 09:35:45
1. Purchased a 2" angle bracket from Lowes, increased hole sizes to suit and trimed with my grinder cut off wheel. 2. New 5/16X3/4 SS bolt (the one supplied was too long) 3. Existing frame bolt needed to be inserted into angle bracket before SS nut could be installed and tighteded with lock washer and blue locktite.
1. Purchased a 2" angle bracket from Lowes, increased hole sizes to suit and trimed with my grinder cut off wheel. 2. New 5/16X3/4 SS bolt (the one supplied was too long) 3. Existing frame bolt needed to be inserted into angle bracket before SS nut could be installed and tighteded with lock washer and blue locktite.
0 2018/09/03 09:30:13
First step was to remove this Frame bolt
First step was to remove this Frame bolt
0 2018/09/03 09:28:05
Hope you can see this OK
Hope you can see this OK
0 2018/09/01 15:54:13
0 2018/09/01 15:50:12
0 2018/09/01 15:49:08
0 2018/09/01 06:21:16
0 2018/09/01 06:21:14
0 2018/09/01 06:21:14
0 2018/09/01 06:21:12
0 2018/08/22 11:52:51
0 2018/08/22 11:51:02
0 2018/08/22 11:51:01
0 2018/08/21 08:31:43
0 2018/08/18 16:12:46
Drivers view installed. I used the Velcro so when I don't mount the phone, I can undo the Velcro and fold the shied flat to store in the saddlebag so it is with me. If the sun is behind you it may not work, but it should help to be able to read the screen most of the time. It is possible you may want to increase the sides and top to 3" or more, but I did not want it to stick out too far.
Drivers view installed. I used the Velcro so when I don't mount the phone, I can undo the Velcro and fold the shied flat to store in the saddlebag so it is with me. If the sun is behind you it may not work, but it should help to be able to read the screen most of the time. It is possible you may want to increase the sides and top to 3" or more, but I did not want it to stick out too far.
0 2018/08/03 09:30:48
Installed in RAM X-Grip. Note that I cut notches in the shield where the grip clamps onto the phone. Without the notches the grip tended to colapse the poly inwards and did not feel to secure. With the notches the grip grips the phone and not the shield. The piece of Velcro attaching the phone to the shield would not really be needed.
Installed in RAM X-Grip. Note that I cut notches in the shield where the grip clamps onto the phone. Without the notches the grip tended to colapse the poly inwards and did not feel to secure. With the notches the grip grips the phone and not the shield. The piece of Velcro attaching the phone to the shield would not really be needed.
0 2018/08/03 09:23:27
0 2018/08/03 09:20:03
0 2018/08/03 09:19:09
0 2018/08/03 09:18:05
Partialy folded. The bends made at score lines made in the poly gently.
Partialy folded. The bends made at score lines made in the poly gently.
0 2018/08/03 09:15:35
Flipped ove to show the placement of the mating Velcro patches
Flipped ove to show the placement of the mating Velcro patches
0 2018/08/03 09:13:58
Using a sharp utility knife I cut one side of binder as shown. The piece of velco in the middle mates with a piece I put on the back side of my phone. Just wanted to make sure the phone did not slip out of the slippery poly.
Using a sharp utility knife I cut one side of binder as shown. The piece of velco in the middle mates with a piece I put on the back side of my phone. Just wanted to make sure the phone did not slip out of the slippery poly.
0 2018/08/03 09:09:13
My materials fromOffice Depo. Very cheep 1" Black POLY binder and 3 pack of 2'X3" Scotch VELCRO patches.
My materials fromOffice Depo. Very cheep 1" Black POLY binder and 3 pack of 2'X3" Scotch VELCRO patches.
0 2018/08/03 09:04:12
0 2018/07/31 03:08:07
With one 2X8X8' plus some scrap I make this roll up to rais the bike 1 1/2"
With one 2X8X8' plus some scrap I make this roll up to rais the bike 1 1/2"
0 2018/07/27 01:27:47
The extra length of 2X8 tied to the front roll up keeps the Jiffy Stand at the same level as the wheels
The extra length of 2X8 tied to the front roll up keeps the Jiffy Stand at the same level as the wheels
0 2018/07/27 01:27:45
Right side final install
Right side final install
0 2018/07/10 08:31:47
Left side, final install
Left side, final install
0 2018/07/10 08:30:33
0 2018/07/10 08:29:48
Left side flipped up
Left side flipped up
0 2018/07/09 16:43:15
Close up of Left side support installed
Close up of Left side support installed
0 2018/07/09 16:41:12
Left support ground away to clear transmission housing
Left support ground away to clear transmission housing
0 2018/07/09 16:38:57
Left support modified
Left support modified
0 2018/07/09 16:37:40
Left side
Left side
0 2018/07/09 16:36:18
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands