EVO All Evo Model Discussion

Has My Dyna Had The Cams Replaced?

Thread Tools
 
Search this Thread
 
  #1  
Old 03-07-2019, 08:11 AM
VAFish's Avatar
VAFish
VAFish is offline
Grand HDF Member

Thread Starter
Join Date: Nov 2018
Location: Virginia
Posts: 4,493
Received 3,132 Likes on 1,626 Posts
Default Has My Dyna Had The Cams Replaced?

So I'm new to Big Twins, only owned the Dyna since December. Other Harley's are Sportsters.

I was looking at the Low Rider the other day and notice the Push Rod tubes seem to be 2 piece. My Sportsters they are one piece. I ran across a Youtube video where they were doing a cam upgrade and instead of pulling the rocker boxes off they cut the push rods and tubes with a bolt cutter and put in adjustable push rods and a two piece tube.

I know the bike has a K&N air filter, jet kit, and pipes on it.

Just wondering if it has had cam work done on it too?



 
  #2  
Old 03-07-2019, 08:27 AM
flhchaz's Avatar
flhchaz
flhchaz is offline
Club Member
Join Date: Sep 2011
Location: In The Woods, PA
Posts: 2,923
Received 1,286 Likes on 499 Posts
Default

Those are typical push rod tubes for a big twin. If you open them and see that the pushrods have been changed to adjustables, then it is likely that someone has been in the cam chest.
 
  #3  
Old 03-07-2019, 09:57 AM
Prot's Avatar
Prot
Prot is online now
Club Member

Join Date: Aug 2008
Location: Lafayette, Louisiana
Posts: 21,787
Received 14,351 Likes on 6,264 Posts
Default

It probably has a different cam since the timing cover is not OEM / riveted on.
 
  #4  
Old 03-07-2019, 11:18 AM
daven9113's Avatar
daven9113
daven9113 is offline
Road Master
Join Date: Aug 2007
Location: Grew up in Texas, moved to AZ
Posts: 917
Received 293 Likes on 199 Posts
Default

If you are talking about push rods being 2 piece instead of the PR covers, then yes, you would have aftermarket PRs. You could easily pop off the PR covers to check.

If you have aftermarket PRs, you may have a cam upgrade, but not necessary. The only way to find out is to get in there. The other reason a cam cover is replaced is if the pick-up sensor needed replacing.

I'm betting you do have an aftermarket cam, because you have non-stock pipes and free flowing air filter.
 
  #5  
Old 03-07-2019, 11:22 AM
98hotrodfatboy's Avatar
98hotrodfatboy
98hotrodfatboy is offline
Seasoned HDF Member
Join Date: Mar 2010
Location: Poolville
Posts: 17,697
Received 4,891 Likes on 3,350 Posts
Default

Deleted,......
 

Last edited by 98hotrodfatboy; 03-07-2019 at 11:29 AM.
  #6  
Old 03-08-2019, 07:32 AM
splattttttt's Avatar
splattttttt
splattttttt is offline
Ultimate HDF Member

Join Date: Jul 2014
Location: MASS_hole
Posts: 5,652
Received 430 Likes on 379 Posts
Default

Originally Posted by daven9113
If you are talking about push rods being 2 piece instead of the PR covers, then yes, you would have aftermarket PRs. You could easily pop off the PR covers to check.

If you have aftermarket PRs, you may have a cam upgrade, but not necessary. The only way to find out is to get in there. The other reason a cam cover is replaced is if the pick-up sensor needed replacing.

I'm betting you do have an aftermarket cam, because you have non-stock pipes and free flowing air filter.
Is it not possible to upgrade exaust and air cleaner to flow freer than stock on an EVO with out upgradeding cams?
 
  #7  
Old 03-08-2019, 07:38 AM
aces&8s's Avatar
aces&8s
aces&8s is offline
Ultimate HDF Member
Join Date: Sep 2012
Location: almost there
Posts: 6,567
Received 574 Likes on 380 Posts
Default

Originally Posted by splattttttt
Is it not possible to upgrade exaust and air cleaner to flow freer than stock on an EVO with out upgradeding cams?
On a 20+ yr old bike with changed pipes, breather and cam cover I would say its a good bet the cam been updated with new bearings.
 
  #8  
Old 03-08-2019, 07:47 AM
splattttttt's Avatar
splattttttt
splattttttt is offline
Ultimate HDF Member

Join Date: Jul 2014
Location: MASS_hole
Posts: 5,652
Received 430 Likes on 379 Posts
Default

Yeah, but does the cam need upgrading if you go with after market exhaust and breather?
 
  #9  
Old 03-08-2019, 07:54 AM
Racepres's Avatar
Racepres
Racepres is offline
Seasoned HDF Member
Join Date: Jul 2014
Location: Cental, MI
Posts: 6,942
Received 2,056 Likes on 1,511 Posts
Default

Originally Posted by splattttttt
Yeah, but does the cam need upgrading if you go with after market exhaust and breather?
If it had an "L" cam... probably no... but... being a Dyna... I'm betting if it don't have a Cam... It needs one.
 
  #10  
Old 03-08-2019, 08:19 AM
daven9113's Avatar
daven9113
daven9113 is offline
Road Master
Join Date: Aug 2007
Location: Grew up in Texas, moved to AZ
Posts: 917
Received 293 Likes on 199 Posts
Default

Originally Posted by splattttttt
Yeah, but does the cam need upgrading if you go with after market exhaust and breather?
Answer is no, as Racepres said. Exhaust and breather is normally the first steps of Stage 1 build.

I'm willing to bet that the bike already has a cam. Look at the chrome upgrades on that bike. Someone spent a little money putting that on, and probably would have put a cam in the bike with other upgrades. Again, the only real way to find out is open her up.
 


Quick Reply: Has My Dyna Had The Cams Replaced?



All times are GMT -5. The time now is 07:13 PM.