Harley Davidson Forums
Sealed up the speaker mount and added some Soundmat to the lid top. Hoping to keep the latches and hinges from rattling.
Sealed up the speaker mount and added some Soundmat to the lid top. Hoping to keep the latches and hinges from rattling.
0 2021/08/01 18:31:32
All together with the speaker mounted. Also cut and modified my underlid Saddlemen storage system. Lost on side, but always good to have some pockets to store stuff
All together with the speaker mounted. Also cut and modified my underlid Saddlemen storage system. Lost on side, but always good to have some pockets to store stuff
0 2021/08/01 18:31:37
Bags all back together and ready to mount once I get the wiring wrapped up.
Bags all back together and ready to mount once I get the wiring wrapped up.
0 2021/08/01 18:31:41
Going to make a smaller rack to hold the amp right on top of radio. Will add some holes in the rack to allow air flow. DSR1 will mount on the right using the holes in the speaker pod to mount it. The power distribution blocks will be mounted in the left, going to make a small shelf to hold them above the glove box.
Going to make a smaller rack to hold the amp right on top of radio. Will add some holes in the rack to allow air flow. DSR1 will mount on the right using the holes in the speaker pod to mount it. The power distribution blocks will be mounted in the left, going to make a small shelf to hold them above the glove box.
0 2021/08/01 18:31:45
New plate. Mounts to too do GTS radio. When I mounted the amps and test fit the fairing, it was just touching. So re-drilled the mount holes and moved back a bit to give adequate clearance.
New plate. Mounts to too do GTS radio. When I mounted the amps and test fit the fairing, it was just touching. So re-drilled the mount holes and moved back a bit to give adequate clearance.
0 2021/08/02 20:06:31
Amps mounted and the they clear finally. DSP mounts on a plate on right hand side using the speaker pod mounting holes. Have to remake the “shelf” on the left side to hold the power distribution blocks.
Amps mounted and the they clear finally. DSP mounts on a plate on right hand side using the speaker pod mounting holes. Have to remake the “shelf” on the left side to hold the power distribution blocks.
0 2021/08/02 20:06:38
Fits in nicely.
Fits in nicely.
0 2021/08/03 20:01:20
Nice and solid mounting for the power and ground distribution blocks. Got the 8ga remade and ran from the blocks to the amps.
Nice and solid mounting for the power and ground distribution blocks. Got the 8ga remade and ran from the blocks to the amps.
0 2021/08/03 20:01:25
Fairing all buttoned up. Ready to set gains, then hook speakers back up and close it all up.
Fairing all buttoned up. Ready to set gains, then hook speakers back up and close it all up.
0 2021/08/07 19:58:12
Ended up having to take out the factory cover that fits above the battery. Gives me much more room. And everything fits great. Took some measurements and going to 3D print some caps for the terminals just to make sure nothing crosses them.
Ended up having to take out the factory cover that fits above the battery. Gives me much more room. And everything fits great. Took some measurements and going to 3D print some caps for the terminals just to make sure nothing crosses them.
0 2021/08/07 19:58:22
Speakers look good in the bags. Have a small rub when it closes if I don’t lift up a little. Ordered some 1/2” spacers, but not sure that will solve the problem. Will just have to be careful. Maybe out a little abrasion tape on the speaker edge.
Speakers look good in the bags. Have a small rub when it closes if I don’t lift up a little. Ordered some 1/2” spacers, but not sure that will solve the problem. Will just have to be careful. Maybe out a little abrasion tape on the speaker edge.
0 2021/08/07 19:58:33
Love the look of the ass end with the new lids.
Love the look of the ass end with the new lids.
0 2021/08/07 19:58:38
0 2022/02/28 10:02:00
0 2025/02/08 15:55:33
0 2025/01/31 12:00:28
0 2025/01/31 12:00:43
0 2025/02/01 14:46:16
0 2025/02/01 14:46:19
0 2025/02/08 15:55:29
0 2025/02/08 15:55:37
0 2025/02/08 15:55:40
0 2025/02/08 16:02:27
0 2025/02/09 12:45:47
0 2025/02/09 12:47:14
0 2025/02/23 13:50:23
0 2025/02/23 13:50:26
Pretty decent :)
Pretty decent :)
0 2025/06/05 17:50:38
New 4-3/8” Darkhorse flywheel
New 4-3/8” Darkhorse flywheel
0 2025/06/05 17:50:40
TIMKEN bearing upgrade
TIMKEN bearing upgrade
0 2025/06/05 17:50:44
Darkhorse competition rods
Darkhorse competition rods
0 2025/06/05 17:50:46
This was zip tied to the case. Not sure what they are???
This was zip tied to the case. Not sure what they are???
0 2025/06/05 17:50:49
0 2025/06/07 16:10:24
0 2025/06/08 16:43:54
0 2025/06/12 15:59:55
0 2025/06/12 15:59:59
Originally was using Xmas ornament hooks. But handling each one was not going well. Also, the faraday effect was killing me with the large hook. Used some channel looks and some utility wire I had, and bent up a bunch of these. Could get 12 on a strip, and the shape helped eliminate the faraday effect.
Originally was using Xmas ornament hooks. But handling each one was not going well. Also, the faraday effect was killing me with the large hook. Used some channel looks and some utility wire I had, and bent up a bunch of these. Could get 12 on a strip, and the shape helped eliminate the faraday effect.
0 2025/06/15 16:09:28
About 1/2 of them all done.
About 1/2 of them all done.
0 2025/06/15 16:09:32
0 2025/06/20 16:45:13
So easy to install when nothing is in your way.
So easy to install when nothing is in your way.
0 2025/06/20 16:45:22
0 2025/06/20 16:45:26
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands