Harley Davidson Forums
0 2025/06/20 16:45:18
0 2025/06/20 16:45:29
Covers are going to be powder coated. Had to move my setup to work, too messy for my garage.
Covers are going to be powder coated. Had to move my setup to work, too messy for my garage.
0 2025/06/21 16:02:24
Got the Baker shifter pawl and shifter arm also. Just weight of the material is almost double stock. Much stronger steel. Hopefully will never have to worry about the splines stripping.
Got the Baker shifter pawl and shifter arm also. Just weight of the material is almost double stock. Much stronger steel. Hopefully will never have to worry about the splines stripping.
0 2025/06/21 16:02:28
ARP not going to fit on trans cover. Will pick up some polished SS SHCS to use here. Added the Fuel Moto trans vent.
ARP not going to fit on trans cover. Will pick up some polished SS SHCS to use here. Added the Fuel Moto trans vent.
0 2025/06/28 17:09:42
Finally found the quad seal in my stack of shit so I could get the backside of the trans covered up. Going with the Bearing conversion for the race.
Finally found the quad seal in my stack of shit so I could get the backside of the trans covered up. Going with the Bearing conversion for the race.
0 2025/06/28 17:09:46
0 2025/07/08 10:57:51
0 2025/07/09 08:31:40
0 2025/07/11 17:54:56
0 2025/07/11 17:55:00
0 2025/07/13 07:52:07
0 2025/07/13 07:52:11
Tubes are in good shape fortunately, one thing at least to save some cost.
Tubes are in good shape fortunately, one thing at least to save some cost.
0 2025/07/13 07:58:06
Few small dings I need to weld back in and clean up. Overall in good shape.
Few small dings I need to weld back in and clean up. Overall in good shape.
0 2025/07/13 07:58:10
Stock FXD axle on left, Stock 49mm axle in middle, and the Vulcan conversion axle on the right. Definitely going to need some spacers.
Stock FXD axle on left, Stock 49mm axle in middle, and the Vulcan conversion axle on the right. Definitely going to need some spacers.
0 2025/07/13 07:58:13
0 2025/07/15 08:27:54
0 2025/07/15 08:27:56
0 2025/07/20 11:18:43
0 2025/07/20 11:18:49
0 2025/07/20 11:18:47
The flange seal is on the orange jack. Not sure where it goes. Everything seems to fit without it.
The flange seal is on the orange jack. Not sure where it goes. Everything seems to fit without it.
0 2025/07/27 16:31:10
0 2025/07/27 16:31:14
Confused about part #1, instructions say to put it on first, but where?
Confused about part #1, instructions say to put it on first, but where?
0 2025/07/27 16:31:16
Barnett Scorpion Clutch
Barnett Scorpion Clutch
0 2025/08/02 14:26:00
Got wheels back from powder coater
Got wheels back from powder coater
0 2025/08/02 14:26:07
Inner primary pretty much buttoned up
Inner primary pretty much buttoned up
0 2025/08/02 14:26:03
Fork tube lowers back also
Fork tube lowers back also
0 2025/08/02 14:26:09
0 2025/08/09 18:32:38
0 2025/08/09 18:32:41
0 2025/08/09 18:32:54
0 2025/08/13 20:07:23
0 2025/08/13 20:07:31
0 2025/08/15 19:05:44
0 2025/08/15 19:05:50
Forgot to take a photo before I mounted the wheel of the spacer I machined.
Forgot to take a photo before I mounted the wheel of the spacer I machined.
0 2025/08/15 19:05:53
0 2025/09/01 19:38:55
0 2025/09/01 19:38:59
 
 
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands