Kw miswiring message
Thread Starter
|
Seasoned HDF Member
Joined: Mar 2012
Posts: 5,157
Likes: 740
From: new caney, tx
Kw miswiring message
Rode to a friend's house yesterday and everything was fine, 10 hour later I get a miswiring, check wiring and turn off message ok the head unit. This morning I ran new wires for the speakers which is what I've read is most likely to cause that message.. That didn't help any, I reset the HU, tried moving around wires to see if I had another short and still nothing. Then I noticed the amp isn't powering on, maybe because the remote from the HU is powering it on.. Any ideas guys.. B2 amp, Kenwood 562 hu
Stellar HDF Member
Joined: Aug 2014
Posts: 2,843
Likes: 574
From: Lockport Illinois
Kw miswiring message
Rode to a friend's house yesterday and everything was fine, 10 hour later I get a miswiring, check wiring and turn off message ok the head unit. This morning I ran new wires for the speakers which is what I've read is most likely to cause that message.. That didn't help any, I reset the HU, tried moving around wires to see if I had another short and still nothing. Then I noticed the amp isn't powering on, maybe because the remote from the HU is powering it on.. Any ideas guys.. B2 amp, Kenwood 562 hu
If all is good the amp should have an internal fuse that may have popped
Thread Starter
|
Seasoned HDF Member
Joined: Mar 2012
Posts: 5,157
Likes: 740
From: new caney, tx
I assume I have it narrowed down to the HU itself. I unplugged every possible connection I could except the 3 wires from the HU harness to the axxis because they are soldered. I'm still getting the message, without anything else being hooked up I don't see what could be miswired
Grand HDF Member
Joined: Aug 2014
Posts: 3,609
Likes: 1,601
From: Eastern Ohio
Try doing a factory reset on the hu.
Make sure none of your speaker outputs on the hu are grounding out, skinned, or pinched.
You could try putting a ground wire from the chassis of the hu to a grounded location on the bike. Some hus I had back in the car audio days were picky about having a chassis ground.
Make sure it has the latest firmware update.
Good luck. I know you need your Pantera when you're riding.
Make sure none of your speaker outputs on the hu are grounding out, skinned, or pinched.
You could try putting a ground wire from the chassis of the hu to a grounded location on the bike. Some hus I had back in the car audio days were picky about having a chassis ground.
Make sure it has the latest firmware update.
Good luck. I know you need your Pantera when you're riding.
Thread Starter
|
Seasoned HDF Member
Joined: Mar 2012
Posts: 5,157
Likes: 740
From: new caney, tx
I didn't have any speaker wires hooked to the HU at all just the ones thay were connected to the axxis and it still says the same thing. I tried wiring the speakers directly to the HU and the way it was which is thru the amp and nothing.. However 2 times throughout the day it would work and as soon as I'd turn it off it would work again
Trending Topics
Road Master
Joined: Aug 2014
Posts: 783
Likes: 13
From: Indiana
Mw Message
Been awhile...which 3 are connected to the axxess? Hate to say it but maybe cut and resolder? Grasping at straws...
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
10 Things Harley-Davidson Needs to Fix in 2026
Verdad Gallardo
Thread Starter
|
Seasoned HDF Member
Joined: Mar 2012
Posts: 5,157
Likes: 740
From: new caney, tx
Not sure what I did but it's workin fine now.. I had everything disconnected for 2 days and went out this morning to re do everything, every u used wire is capped off and stuffed inside some loom.. Now I get to go back and redo all of the damn settings again which is my least favorite part lol