LED turn signal conversion
Stellar HDF Member
Joined: May 2010
Posts: 2,864
Likes: 127
From: Aussie lost in Switzerland
Seasoned HDF Member
Joined: Nov 2016
Posts: 5,801
Likes: 809
From: South Carolina
Stupid question here... How much does this conversion cost? and time?
I know that running the wire through the turn signal tunnel on the rear was a PIA! The I started that and quickly started looking for a new solution.
So plug and go was my choice, took a long time total of five minutes! I four of which was the seat.
I know that running the wire through the turn signal tunnel on the rear was a PIA! The I started that and quickly started looking for a new solution.
So plug and go was my choice, took a long time total of five minutes! I four of which was the seat.
Thread Starter
|
Tourer
Joined: Jun 2016
Posts: 396
Likes: 20
From: Maple Ridge BC & Chiangmai
Bought a bike specific part on-line here in Thailand rather than cobble it together myself, and try and make a heat sink. AliExpress is full of such devices.
https://www.lazada.co.th/4x-turn-sig...336a9da2C43i5R
7.20 USD for all 4, including delivery to my door, and I will have them in 3 days
Given that it is nothing more than a resistor, I am hard pressed to import a plug and play one. Even if I was back in Canada, I would still go this route, as I am wiring anyway.
Installation is easy as Krazy8's indicates and simply a matter of soldering this across each indicator lead. I have to wire in new mini LED indicators anyway so no big deal.
More than 5 min but works for me
https://www.lazada.co.th/4x-turn-sig...336a9da2C43i5R
7.20 USD for all 4, including delivery to my door, and I will have them in 3 days
Given that it is nothing more than a resistor, I am hard pressed to import a plug and play one. Even if I was back in Canada, I would still go this route, as I am wiring anyway.
Installation is easy as Krazy8's indicates and simply a matter of soldering this across each indicator lead. I have to wire in new mini LED indicators anyway so no big deal.
More than 5 min but works for me
Seasoned HDF Member
Joined: Nov 2016
Posts: 5,801
Likes: 809
From: South Carolina
Bought a bike specific part on-line here in Thailand rather than cobble it together myself, and try and make a heat sink. AliExpress is full of such devices.
https://www.lazada.co.th/4x-turn-sig...336a9da2C43i5R
7.20 USD for all 4, including delivery to my door, and I will have them in 3 days
Given that it is nothing more than a resistor, I am hard pressed to import a plug and play one. Even if I was back in Canada, I would still go this route, as I am wiring anyway.
Installation is easy as Krazy8's indicates and simply a matter of soldering this across each indicator lead. I have to wire in new mini LED indicators anyway so no big deal.
More than 5 min but works for me
https://www.lazada.co.th/4x-turn-sig...336a9da2C43i5R
7.20 USD for all 4, including delivery to my door, and I will have them in 3 days
Given that it is nothing more than a resistor, I am hard pressed to import a plug and play one. Even if I was back in Canada, I would still go this route, as I am wiring anyway.
Installation is easy as Krazy8's indicates and simply a matter of soldering this across each indicator lead. I have to wire in new mini LED indicators anyway so no big deal.
More than 5 min but works for me
Thread
Thread Starter
Forum
Replies
Last Post
GRooVyCon
Ignition/Tuner/ECM/Fuel Injection
2
Jul 26, 2018 07:25 AM
