Induction Module after Jump Start?
Thread Starter
|
Stellar HDF Member
Joined: Mar 2009
Posts: 2,454
Likes: 58
From: Graysville, AL
Induction Module after Jump Start?
Hello, I'm trying to diagnose an issue on a buddies 14 Street Glide Special. He tried jump starting the bike with his truck with no luck. Now the bike will not idle and will only stay running if you hold the throttle wide open. I've attached a pic of the codes it is throwing. Everything I read says it is the induction module but before spending 200.00 I wanted to get some opinions.
Well the image would not upload. Here are the codes I pulled.
P1511- ETC Power Management Mode
P2100- ETC Driver Open Circuit
P2176- ETC Zero Position Learning Error
This is what I've done so far.
disconnect the batter and computer overnight. Charged the battery.
Turn the switch on/off 4 times to reset the TPS.
Checked all fuses.
Cleared codes.
Well the image would not upload. Here are the codes I pulled.
P1511- ETC Power Management Mode
P2100- ETC Driver Open Circuit
P2176- ETC Zero Position Learning Error
This is what I've done so far.
disconnect the batter and computer overnight. Charged the battery.
Turn the switch on/off 4 times to reset the TPS.
Checked all fuses.
Cleared codes.
Last edited by lhgdale; Jun 6, 2019 at 07:09 AM.
Elite HDF Member
Joined: Nov 2005
Posts: 3,654
Likes: 362
From: Mansfield Texas
I have also read to do the relearn .... With the run switch in the on position, turn on ignition switch. wait for engine light to go out, turn ignition switch off Repeat this 4 times with the ignition switch but leave the run switch on.
You should hear noise from the throttle body. Good Luck.
You should hear noise from the throttle body. Good Luck.
Ultimate HDF Member
Joined: Apr 2014
Posts: 6,322
Likes: 2,500
From: Tennessee
Never jump a bike from a running car or truck....Good way to fry ****.
Elite HDF Member
Joined: Nov 2005
Posts: 3,654
Likes: 362
From: Mansfield Texas
Yep, the car battery alone is enough to start a bike, with the car/truck running he let the smoke out of something, I am willing to bet the throttle control module is gone.
Last edited by barrygreen; Jun 6, 2019 at 09:24 AM.
Thread Starter
|
Stellar HDF Member
Joined: Mar 2009
Posts: 2,454
Likes: 58
From: Graysville, AL
He learned the hard way about jump starting the bike. Searching the trouble code fixes and they all seem to point to the induction module.
Trending Topics
Elite HDF Member
Joined: Nov 2005
Posts: 3,654
Likes: 362
From: Mansfield Texas
Might try looking for one used from someone who went to a larger throttle body, places like Fuel Moto or GMR Performance , they might have one laying around.
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
10 Things Harley-Davidson Needs to Fix in 2026
Verdad Gallardo
Elite HDF Member
Joined: Nov 2005
Posts: 3,654
Likes: 362
From: Mansfield Texas
These work well, plus they have USB ports to charge phones and other things.
https://www.carbatterychargerscentra...jump-starters/
https://www.carbatterychargerscentra...jump-starters/