Help! need help adjusting a clutch pack.
Thread Starter
|
Road Captain
Joined: Dec 2008
Posts: 643
Likes: 0
From: Sioux Falls, SD
Help! need help adjusting a clutch pack.
I need help adjusting my clutch able and pack.
1. on the cable just some clarification. I assume up is tight and down is loose, is this correct?
2. when I try to loosen the nut on my clutchpack the clutch spins. How do I stop this?
3. I recieved the large round gasket that goes on the outside instead of the thin one that goes on the inside
Thanks
1. on the cable just some clarification. I assume up is tight and down is loose, is this correct?
2. when I try to loosen the nut on my clutchpack the clutch spins. How do I stop this?
3. I recieved the large round gasket that goes on the outside instead of the thin one that goes on the inside
Thanks
Elite HDF Member
Joined: Sep 2008
Posts: 4,440
Likes: 148
From: Northwest
Baker, take a look.... this may help:
http://www.expertvillage.com/video/1...clutch-one.htm
http://www.expertvillage.com/video/1...clutch-two.htm
http://www.expertvillage.com/video/1...clutch-one.htm
http://www.expertvillage.com/video/1...clutch-two.htm
Thread Starter
|
Road Captain
Joined: Dec 2008
Posts: 643
Likes: 0
From: Sioux Falls, SD
Those are good but not very descriptive.
Iwas able to figure out, up is loose on the cable, but and the clutch is harder to turn, but still spins.
cable is all the way loose.
Iwas able to figure out, up is loose on the cable, but and the clutch is harder to turn, but still spins.
cable is all the way loose.
Thread Starter
|
Road Captain
Joined: Dec 2008
Posts: 643
Likes: 0
From: Sioux Falls, SD
Its adjusting the clutch I have a problem with. When I try to unscrew the nut on the lutch pack, or the hex bolt in the clutch pack, the clutch turns.
Also is the standard true, left loose right tight?
Also is the standard true, left loose right tight?
Club Member
Joined: Jul 2008
Posts: 112,202
Likes: 1,316
From: On a hill among the hills, PA
Trending Topics
Road Warrior
Joined: May 2008
Posts: 1,955
Likes: 6
From: Little Rock
you need an allen wrench in the center screw and a wrench on the outer nut... turn the nut counter clockwise while holding the center shaft from moving with the allen wrench.. i reccomend a service manual to if you dont already have one..
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
10 Things Harley-Davidson Needs to Fix in 2026
Verdad Gallardo
Club Member
Joined: Jul 2008
Posts: 112,202
Likes: 1,316
From: On a hill among the hills, PA
+1 on this way also... watch your knuckles!!!