Easy pull clutch gizmo
Road Captain
Joined: Feb 2009
Posts: 690
Likes: 0
From: Huntington Beach, SoCal
I installed the Harley version (#36808-05 )on my wife's 03 Heritage and it definitely reduced the amount of pressure required for the clutch lever. It was an easy install (about 45 minutes).
Road Captain
Joined: Jun 2008
Posts: 572
Likes: 6
From: Ft. Worth, Texas
IMO the best easy pull clutch is as stated above, the Harley kit with the reduce effort clutch pack spring and the new ramp assy. I hate those burlybike things. I take em off bikes all the time.
This is definately one area where H-D got it right with the easypull kit. Thats the only true way to reduce effort without crazy contraptions to give you more leverage and still dont work as well as the H-D kit
This is definately one area where H-D got it right with the easypull kit. Thats the only true way to reduce effort without crazy contraptions to give you more leverage and still dont work as well as the H-D kit
Ultimate HDF Member
Joined: Oct 2007
Posts: 7,562
Likes: 11
From: Palm Harbor fl.
on the harley kit, where does the clutch spring go? Does it require the clutch plates to be taken apart or is the whole kit installed behind the clutch cover where the cable goes?
Tourer
Joined: Sep 2008
Posts: 497
Likes: 15
i bought the plate and ramps from amercian classics motors and what they sent me was stock parts...my friend has the correct ramps and as in ur picture the throw,,,or groove is bigger ,,but it works...i have rheumatoid arthritis and hard clutches hurt my hands so i went with this,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Road Captain
Joined: Jun 2008
Posts: 572
Likes: 6
From: Ft. Worth, Texas
The new ball ramp assy is installed behind the tranny cover on the right side and the spring is the diaphram spring installed in the clutch pack. To install the spring you will have to pull the outer primary and use a compressor tool to compress the stock spring to remove it. Sounds like a lot of work but its pretty simple if you can get ahold of the tool to do it.
Road Warrior
Joined: Dec 2007
Posts: 1,452
Likes: 2
From: Maryland
you will need to pull the outer prinary off and remove 6-8 little bolts put some blue lockitie on and tighten you will need 2 gaskets a trans door and a primary
Elite HDF Member
Joined: Apr 2009
Posts: 3,928
Likes: 1
From: Desert S. West
The HD easy clutch kit works very well but be aware that it will cause the clutch's to eventually slip if you have a built motor. Another thing some people are not aware of is if the clutch cable has a plastic (PVC) liner then it shouldn't be oiled. Oiling can cause the clutch lever to be harder to pull.
I installed the Burly type kit and it reduced the pull tension by about 50%.
I installed the Burly type kit and it reduced the pull tension by about 50%.
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski