Rear wheel install
Thread Starter
|
6th Gear
Joined: Apr 2019
Posts: 14
Likes: 1
From: New England
Rear wheel install
All, I’m having issues with an install of my rear wheel on a 97 road king.
I had some new tires put on and after reinstalling my rear wheel, the sprocket rubs on the swing arm once the nut gets anywhere close to torqued.
The wheel is aligned, when checked at 15 or so ft/lbs, larger wheel spacer is on belt side. I’m at a loss I’m assuming it’s a simple solution that I just can’t see.
thanks
I had some new tires put on and after reinstalling my rear wheel, the sprocket rubs on the swing arm once the nut gets anywhere close to torqued.
The wheel is aligned, when checked at 15 or so ft/lbs, larger wheel spacer is on belt side. I’m at a loss I’m assuming it’s a simple solution that I just can’t see.
thanks
Seasoned HDF Member
Joined: May 2008
Posts: 21,180
Likes: 12,757
From: South Carolina
You have 2 spacers that are the same size, one on each side, they go up against the bearing inner race.
The left side has an additional spacer that goes outside of the first spacer.
You are missing one of the spacers.
The left side has an additional spacer that goes outside of the first spacer.
You are missing one of the spacers.
Last edited by Dan89FLSTC; Jul 12, 2020 at 09:54 AM.
HDF Community Team
Joined: Dec 2005
Posts: 5,428
Likes: 2,624
From: NC USA
Unless you took the inner spacers out of the seals before the trip to the tire store, good chance one of your spacers in on their floor, or in whatever vehicle you drove there...
And you should ALWAYS service wheel bearings before installation, after changing a tire
And you should ALWAYS service wheel bearings before installation, after changing a tire
Last edited by t150vej; Jul 12, 2020 at 10:19 AM.
Trending Topics
Thread Starter
|
6th Gear
Joined: Apr 2019
Posts: 14
Likes: 1
From: New England
It looks like I have all the parts. 2 inners a larger and a smaller outer.... Ill try and reinstall I guess 🤷🏼♂️
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
HDF Community Team
Joined: Dec 2005
Posts: 5,428
Likes: 2,624
From: NC USA
There are the 2 that fit into the seals, long one on the pulley side and the caliper mount is the spacer for the right side. What's this smaller outer you mention?
If it's a thin, stepped washer looking thing, that goes between the inner bearing spacer and a bearing.
Did you take the wheel bearings out?
Last edited by t150vej; Jul 12, 2020 at 11:07 AM.
Thread Starter
|
6th Gear
Joined: Apr 2019
Posts: 14
Likes: 1
From: New England
???????????
There are the 2 that fit into the seals, long one on the pulley side and the caliper mount is the spacer for the right side. What's this smaller outer you mention?
If it's a thin, stepped washer looking thing, that goes between the inner bearing spacer and a bearing.
Did you take the wheel bearings out?
There are the 2 that fit into the seals, long one on the pulley side and the caliper mount is the spacer for the right side. What's this smaller outer you mention?
If it's a thin, stepped washer looking thing, that goes between the inner bearing spacer and a bearing.
Did you take the wheel bearings out?
