2010 Fat Boy Lo - I like it
Advanced
Joined: Jul 2007
Posts: 96
Likes: 0
From: Southeast Florida
Believe me, that was one of the most exhaustive installs I've ever done...diagram the pin-out, double check it, triple check it....unpin the couplers, install the wire extensions, re-pin the couplers, re-install the seals and endcaps ( I had one of the seals outside of the endcap and had to unpin the entire coupler and start all over again, then I put the endcap on backwards!!!!!) pain in the azz...check it before re-installing the tank, alls good. Re-install the tank right turn signal no longer works!!! Screw it, ride the weeekend without it, take it apart Sunday night, the heat shrink had pulled on one wire when I re-installed the tank....
But when all is said and done I do like those street slammers, and would consider doing it all over again....
But when all is said and done I do like those street slammers, and would consider doing it all over again....
6th Gear
Joined: Jul 2010
Posts: 10
Likes: 0
Pipes?
I am getting a 2011 Fat Boy Lo and been lookin at pipes?
What to choose, I really like the V & H and heard them on you tube but I found some Supper Trap Crack Pipes pipes too any one out htere with Supper Traps?
just thinking?
What to choose, I really like the V & H and heard them on you tube but I found some Supper Trap Crack Pipes pipes too any one out htere with Supper Traps?
just thinking?
Advanced
Joined: Oct 2009
Posts: 59
Likes: 0
Any of you guys that will send me those fat boy lo bars, I'll take 'em. I like low bars and would be happy to pay shipping. I have a'08 fat boy e-mail me rdubarton@etcmail.com I'm in N.GA
Outstanding HDF Member
Joined: Jun 2006
Posts: 2,196
Likes: 13
From: Maryland
Any of you guys that will send me those fat boy lo bars, I'll take 'em. I like low bars and would be happy to pay shipping. I have a'08 fat boy e-mail me rdubarton@etcmail.com I'm in N.GA
6th Gear
Joined: Sep 2011
Posts: 11
Likes: 0
From: Utah
I am looking to get the following stuff PC'd and want to know a guestimate of how tough it will be, who to go to, and how much it will run me. Any help would really be appreciated.
Forks and sliders
Headlight and trim ring
Primary cover
Cylinder covers
Tailight rails
Dash
Rims
Forks and sliders
Headlight and trim ring
Primary cover
Cylinder covers
Tailight rails
Dash
Rims
Cruiser
Joined: Dec 2009
Posts: 131
Likes: 2
From: Four Oaks, North Carolina
Powder Coating Question
Hey Dozer8356, it shouldn't cost you very much to get what you have listed pc. I had alot of the things you have listed pc while my FB Lo was in for the 10,000 service. I just had the guy take the parts off while the bike was in the shop and it onlyh took 3-5 days to get the stuff back from the powder coater. I would guess you could get out for just the powder coating for around $500 +/-.
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
6th Gear
Joined: Sep 2011
Posts: 11
Likes: 0
From: Utah
Hey Dozer8356, it shouldn't cost you very much to get what you have listed pc. I had alot of the things you have listed pc while my FB Lo was in for the 10,000 service. I just had the guy take the parts off while the bike was in the shop and it onlyh took 3-5 days to get the stuff back from the powder coater. I would guess you could get out for just the powder coating for around $500 +/-.
Outstanding HDF Member
Joined: Nov 2010
Posts: 2,033
Likes: 7
From: TEXAS
if your gonna do your wheels along with everything else you can expect $500 for labor and another $200 for PCing. The wheels are gonna be the kicker here.
Last edited by JIMSFBL; Oct 10, 2011 at 02:31 PM.