Engine Compression Problem-
Thread Starter
|
Road Warrior
Joined: Apr 2006
Posts: 1,621
Likes: 1
From: Matthews, NC
Engine Compression Problem-
I was told today by my HD mechanic that the compression of both front and rear is 210. He told me that normal is around 150. He is going to contact HD and find out what the plan of action should be. He thinks that the pistons and rings need to be replaced. Since the bike is under warranty, I am not worried. I have been having trouble starting the bike after it is hot, and after running a bunch of tests, he discovered this issue. What causes compression problems?
Last edited by russl179; Sep 13, 2008 at 07:47 PM. Reason: add more stuff
Thread Starter
|
Road Warrior
Joined: Apr 2006
Posts: 1,621
Likes: 1
From: Matthews, NC
Yes. I do not know what the numbers really mean, but he stated he never seen the compression, in both front and back, so high.
Last edited by russl179; Sep 13, 2008 at 07:51 PM. Reason: mistake
Elite HDF Member
Joined: Sep 2007
Posts: 4,468
Likes: 12
From: Bluffton, South Carolina
Your HD mechanic is no mechanic. If the rings were bad you would have lower not higher compression. If anything your something in your valve train is screwed up and not opening the valves soon enough. Could even be the oil pump not making enough pressure/volume to keep the lifters operating properly. When did the hard starting begin??
Trending Topics
Advanced
Joined: Mar 2008
Posts: 87
Likes: 0
From: West Coast Canada
This is definately not a piston/rings issue. If they were faulty in any way, you would have the opposite.....low compression. Unless there is so much carbon build-up it is raising the compression. I doubt it. Both Cyls are the same. 210 is what I like to see with the builds I do, it's high for a stock motor. A leak down test will confirm that too, and would be mandatory in this troubleshooting sequence. You would think qualified personel would be checking the easy stuff first? KISS principle.... (Keep It Simple Stupid) I would be checking all that would/can affect compression, cams/cam timing/pushrods/rockers etc. All done without "opening up" the engine. Start easy, work up.......but then again I'm not into unnessessary extra work???
Copter
Copter
Last edited by helikenny; Sep 14, 2008 at 08:59 AM. Reason: revise information
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Tourer
Joined: Apr 2007
Posts: 266
Likes: 0
From: Georgia
Agreed, not likely to be rings and pistons UNLESS it has some racing pistons with high compression. It ought to be a very strong runner; if the only problem is hard starting when hot, get the auto compression release (for each cylinder head).
Supporter
Joined: Sep 2006
Posts: 1,245
Likes: 69
From: Northford, CT
There is nothing wrong with the rings or pistons. As everyone has said you will have low compression if there was a problem with them. Look into valve train for your problem. Don't touch the rings or pistons.
Your tech is not very good if he thinks to much compression is the problem.
Your tech is not very good if he thinks to much compression is the problem.
