Smart siren security system
Sponsor
Joined: Jul 2015
Posts: 8,538
Likes: 1,646
From: SF Bay area
You can put it in "transport mode"...
To Enter Transport Mode
1. With an assigned fob within range, turn the ignition switch
to IGN.
2. Before the security system lamp goes out, turn the ignition
switch to OFF.
3. Within three seconds, simultaneously press both the left
and the right turn signal switches.
4. After the turn signals flash once, the system enters the
transport mode. With the fob removed, the motorcycle can
be moved without setting off the alarm.
To Exit Transport Mode
With the fob present, turn the ignition switch to IGN to disarm
the system.
__________________________________________________ ____
For ROCKOUT information & purchasing please click the LINKS below...
To Enter Transport Mode
1. With an assigned fob within range, turn the ignition switch
to IGN.
2. Before the security system lamp goes out, turn the ignition
switch to OFF.
3. Within three seconds, simultaneously press both the left
and the right turn signal switches.
4. After the turn signals flash once, the system enters the
transport mode. With the fob removed, the motorcycle can
be moved without setting off the alarm.
To Exit Transport Mode
With the fob present, turn the ignition switch to IGN to disarm
the system.
__________________________________________________ ____
For ROCKOUT information & purchasing please click the LINKS below...
__________________
NO, they DON'T all do that!
ROCKOUT rocker shaft inserts... make the tapping STOP! From the guy that FOUND and CURED the problem NO ONE ELSE COULD, thank you for your support!
Ordering & info http://www.rockout.biz On ebay! ... CLICK HERE
Also on amazon.com...
Imitated, never equaled... ROCKOUTS!
Ordering & info http://www.rockout.biz On ebay! ... CLICK HERE
Also on amazon.com...
Imitated, never equaled... ROCKOUTS!
Club Member
Joined: Dec 2007
Posts: 4,192
Likes: 168
From: Knoxville, Tn
Battery Tender
Does it bother you that the tender goes thorough the charge/maintain cycle ? That's exactly how it is supposed to work. Just leave it alone and it will be fine.
You do have to turn on the ignition to pull the main fuse or the siren will sound. If you do pull the main fuse, it will probably drain the battery in the siren and it will not operate until it is charged again or the battery in the siren is replaced.
You do have to turn on the ignition to pull the main fuse or the siren will sound. If you do pull the main fuse, it will probably drain the battery in the siren and it will not operate until it is charged again or the battery in the siren is replaced.
Thread Starter
|
Cruiser
Joined: Dec 2013
Posts: 208
Likes: 17
From: Pittsburgh
Does it bother you that the tender goes thorough the charge/maintain cycle ? That's exactly how it is supposed to work. Just leave it alone and it will be fine.
You do have to turn on the ignition to pull the main fuse or the siren will sound. If you do pull the main fuse, it will probably drain the battery in the siren and it will not operate until it is charged again or the battery in the siren is replaced.
You do have to turn on the ignition to pull the main fuse or the siren will sound. If you do pull the main fuse, it will probably drain the battery in the siren and it will not operate until it is charged again or the battery in the siren is replaced.
Yeah I know it makes total sense. Maybe I'm just too **** in that regard. I never had my battery tender flash on and off like that while it was in storage before. Before I installed the Smart Siren I replaced the NiMi battery. So I know the internal battery is good. I will say that siren is LOUD! 
Thread
Thread Starter
Forum
Replies
Last Post
WilllyD
Dyna Glide Models
13
Jun 14, 2016 07:43 AM
Potato_Potato
Touring Models
4
May 23, 2014 10:38 PM
