2000 FXDX diagnostic trouble codes
Thread Starter
|
1st Gear
Joined: Feb 2011
Posts: 5
Likes: 0
From: Sydney Australia
2000 FXDX diagnostic trouble codes
I have a 2000 FXDX that we have just fitted an S&S T111 engine in (carburettored).
The ECM is the S&S IST unit that comes with the engine.
OK this is what happens
- Turn on ignition
- ENGINE lights in red
- ENGINE light goes out
- ENGINE light comes on again and then goes off
If I start the bike it will run for about half a minute and then it seems to lose power and the ENGINE light comes on again.
I tried the diagnostic trouble codes
1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release odometer reset button.
The odometer shows d01CLr (presumably meaning diagnostic #1 clear)
press odometer reset button - now shows d02SEt (does that mean that diagnostic #2 is set?)
pressing the odometer reset button then displays d03CLr, d04CLr, d05CLr, d06CLr, d07CLr, d08CLr, d09CLr
the next press after that displays CAL 10 (whatever that means)
pressing it again starts the sequence again
What do these codes mean?
The ECM is the S&S IST unit that comes with the engine.
OK this is what happens
- Turn on ignition
- ENGINE lights in red
- ENGINE light goes out
- ENGINE light comes on again and then goes off
If I start the bike it will run for about half a minute and then it seems to lose power and the ENGINE light comes on again.
I tried the diagnostic trouble codes
1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release odometer reset button.
The odometer shows d01CLr (presumably meaning diagnostic #1 clear)
press odometer reset button - now shows d02SEt (does that mean that diagnostic #2 is set?)
pressing the odometer reset button then displays d03CLr, d04CLr, d05CLr, d06CLr, d07CLr, d08CLr, d09CLr
the next press after that displays CAL 10 (whatever that means)
pressing it again starts the sequence again
What do these codes mean?
Club Member
Joined: May 2006
Posts: 14,564
Likes: 9,225
From: the 50s & the 60s
.
I have a 2000 FXDX that we have just fitted an S&S T111 engine in (carburettored).
The ECM is the S&S IST unit that comes with the engine.
The odometer shows d01CLr (presumably meaning diagnostic #1 clear)
press odometer reset button - now shows d02SEt (does that mean that diagnostic #2 is set?)
pressing the odometer reset button then displays d03CLr, d04CLr, d05CLr, d06CLr, d07CLr, d08CLr, d09CLr
the next press after that displays CAL 10 (whatever that means)
pressing it again starts the sequence again
What do these codes mean?
I have a 2000 FXDX that we have just fitted an S&S T111 engine in (carburettored).
The ECM is the S&S IST unit that comes with the engine.
The odometer shows d01CLr (presumably meaning diagnostic #1 clear)
press odometer reset button - now shows d02SEt (does that mean that diagnostic #2 is set?)
pressing the odometer reset button then displays d03CLr, d04CLr, d05CLr, d06CLr, d07CLr, d08CLr, d09CLr
the next press after that displays CAL 10 (whatever that means)
pressing it again starts the sequence again
What do these codes mean?
.
.
might be easiest to call S & S.
.
.
.
Thread
Thread Starter
Forum
Replies
Last Post
dirtracer27x
Ignition/Tuner/ECM/Fuel Injection
2
Aug 24, 2014 02:12 AM
tingland
Ignition/Tuner/ECM/Fuel Injection
0
Jul 15, 2012 03:42 PM
