Drilling and Tapping Help?
Thread Starter
|
Cruiser
Joined: Dec 2008
Posts: 166
Likes: 1
Drilling and Tapping Help?
I need some help...
Imagine you have an aluminum box that you wanted to make into an oil tank.
So I am going to need to drill and tap the box for the oil lines right? How do you go about drilling and tapping aluminum?
I have never attempted this on ANY metal, but in my mind aluminum would be EXTRA easy to screw up.... right?
My next question is would screwing hose adapters (bungs?) into these newly tapped holes be oil tight and able to handle the oil pressure?
Or am I pissing up a rope?
Imagine you have an aluminum box that you wanted to make into an oil tank.
So I am going to need to drill and tap the box for the oil lines right? How do you go about drilling and tapping aluminum?
I have never attempted this on ANY metal, but in my mind aluminum would be EXTRA easy to screw up.... right?
My next question is would screwing hose adapters (bungs?) into these newly tapped holes be oil tight and able to handle the oil pressure?
Or am I pissing up a rope?
Thread Starter
|
Cruiser
Joined: Dec 2008
Posts: 166
Likes: 1
Im talking about REALLY basic help.... telling me to weld something is a lot like me telling you to defy gravity without my mind control device..... tsk tsk.
Heli-Coil sounds fine if it were a stripped hole.. I guess... but there isnt even a hole to begin with.
Am I going to be relegated to taking this to a shop and having it done?
Where is the fun in that?
Heli-Coil sounds fine if it were a stripped hole.. I guess... but there isnt even a hole to begin with.
Am I going to be relegated to taking this to a shop and having it done?
Where is the fun in that?
Outstanding HDF Member
Joined: Jul 2008
Posts: 2,206
Likes: 0
From:
The aluminum box is gonna be too thin to tap for oil lines unless it's at least 1/4" thick. Even that is cutting it too close. You'll need to have something with some thickness welded into the holes in the box so that you can tap it. 
Road Master
Joined: Jul 2008
Posts: 811
Likes: 53
From: Emmett, Idaho
Unless you are a TIG welder (and this seems not to be the case) just take the tank to a machine shop and tell them what you need. It really won't cost much and you actually seem not to have any other option. Aluminum welding is very tricky. A shop is the way to go. By the way, drilling a hold in aluminum is just like steel drilling, only easier as aluminum is soft. Might just as well have the shop drill the holes too since it will be doing the welding for you.
Trending Topics
Thread Starter
|
Cruiser
Joined: Dec 2008
Posts: 166
Likes: 1
seems I need a welding fer dummies book... after this trip to the shop of course.
MIG, and TIG, and STICK... OH MY!
MIG, and TIG, and STICK... OH MY!
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
