Softail Models Standard, Custom, Night Train, Deuce, Springer, Heritage, Fatboy, Deluxe, Rocker and Cross Bones.
Sponsored by:
Sponsored by:

Just tore it down

Thread Tools
 
Search this Thread
 
Old Mar 14, 2009 | 06:51 PM
  #11  
TIPN8R's Avatar
TIPN8R
Thread Starter
|
Stellar HDF Member
Joined: Jun 2006
Posts: 3,481
Likes: 11
From: NJ
Default

Originally Posted by snip0721
the wheel bearings must be pulled. the wheel design doesnt allow them to be pressed.


Already done bud! Races are out.
 
Reply
Old Mar 15, 2009 | 07:36 AM
  #12  
coop57's Avatar
coop57
Tourer
Joined: Feb 2008
Posts: 448
Likes: 0
From: Illinois
Default

Sounds like your takin it up another notch!
Post pics it is sounding like it will be even more bad ***!
 
Reply
Old Mar 15, 2009 | 10:01 AM
  #13  
Jacobi's Avatar
Jacobi
Cruiser
Joined: Mar 2009
Posts: 199
Likes: 0
From: Lincoln, NE
Default

Originally Posted by TIPN8R
Parts are in the shop, should have them back by the end of the week, then time to install.

Got new rubber for the rear too


Was gonna say, looks like one too many burnouts on that current tire. Also, post six, pic two, what does that tire in the top left go on?

-Barry-
 
Reply
Old Mar 15, 2009 | 01:48 PM
  #14  
TIPN8R's Avatar
TIPN8R
Thread Starter
|
Stellar HDF Member
Joined: Jun 2006
Posts: 3,481
Likes: 11
From: NJ
Default

Originally Posted by Jacobi
Was gonna say, looks like one too many burnouts on that current tire. Also, post six, pic two, what does that tire in the top left go on?

-Barry-
Barry, those tires are on my commuter vehicle
39.5 Irok radials





 
Reply
Old Mar 15, 2009 | 02:15 PM
  #15  
powdercoater's Avatar
powdercoater
Road Captain
Joined: Sep 2007
Posts: 748
Likes: 1
Default

Looks like a nice collection of toys!
 
Reply
Old Mar 23, 2009 | 06:48 PM
  #16  
TIPN8R's Avatar
TIPN8R
Thread Starter
|
Stellar HDF Member
Joined: Jun 2006
Posts: 3,481
Likes: 11
From: NJ
Default

Slowly but surely, it will get there.

New rubber is on the rear wheel, and I might say, it's so nice to see what tread actually looks like

Parts is another story.

Got royally screwed by by some a-hole who promised a quick good job, and reality it was a rudy goldberg job at best.

So now I have the wheel and swingarm at a friends place getting it all chemically stripped down and done the right way!

Should have it all back by the weekend, if not early next week. No rush, just want it done right.

As soon as I get it all back, it will be put back together in a few hours as long as I can figure out the right spacer issue. Worse case scenario, take measurements, and bring to work to mill down to spec.

whew... I need a brew




 
Reply
Old Mar 23, 2009 | 08:40 PM
  #17  
Xuallus's Avatar
Xuallus
Road Master
Joined: Nov 2008
Posts: 851
Likes: 1
From: Alberta, Canada
Default

surprised you don't have the bars off too..
 
Reply
Old Mar 23, 2009 | 08:42 PM
  #18  
wildman67's Avatar
wildman67
Extreme HDF Member
Joined: Feb 2006
Posts: 10,853
Likes: 0
From: Maryland
Default

good luck! post some pics when you can!
 
Reply
Old Mar 23, 2009 | 08:45 PM
  #19  
rjmac53's Avatar
rjmac53
Extreme HDF Member
Joined: May 2005
Posts: 16,656
Likes: 13
From: The Big Easy
Default

it's gonna look great...
 
Reply
Old Mar 23, 2009 | 08:45 PM
  #20  
TIPN8R's Avatar
TIPN8R
Thread Starter
|
Stellar HDF Member
Joined: Jun 2006
Posts: 3,481
Likes: 11
From: NJ
Default

Originally Posted by Xuallus
surprised you don't have the bars off too..
Not yet, deciding on converting it over to a 1 cable throttle first, then go from there. Also have to wait a bit. Right now I am working 2nd shift, so I'm not there when UPS shows up, so when I get back on 1st shift around the 2nd week of April, then it's full steam ahead with ordering
This way the old lady don't see squat! LOL
 
Reply



All times are GMT -5. The time now is 03:30 PM.