I pulled the trigger! 2007 Softail Custom FXSTC
Thread Starter
|
Elite HDF Member
Joined: May 2012
Posts: 3,747
Likes: 5
From: Central Cali
ghoticov - that's the stock sissy. It looks wicked without the stock seat attached haha! Mine is the stock sissy also with a solo seat. It bolts to the fender strut.
As for your front sigs, you just need $40-$50 relocation brackets that mount to your fork tubes or lower triple pinch bolt (depending if HD brackets or not). Where your wires are stock and run outside it is a sinch to do. Just make sure you re-route your wires out of the way of binding or getting pinched.
Congrats again on your "pulling the trigger"
As for your front sigs, you just need $40-$50 relocation brackets that mount to your fork tubes or lower triple pinch bolt (depending if HD brackets or not). Where your wires are stock and run outside it is a sinch to do. Just make sure you re-route your wires out of the way of binding or getting pinched.
Congrats again on your "pulling the trigger"
I am trying to find a quick disconnect small sissy bar that I can just pop on when I want to go 2 up but I am having no luck. I found a few on Jp Cycles site but I am not sure it is what I am looking for because their is no pic of it on a bike (and it wasn't a quick disconnect) I just want a small one...seems hard to find.
On the turn sits, I did notice yesterday that the wire where on the outside of the tubes so I did think "this will be easy". My issue is I don't really like the HD ones because they stick so far out. Anyone have any luck with shorter ones?
Thread Starter
|
Elite HDF Member
Joined: May 2012
Posts: 3,747
Likes: 5
From: Central Cali
What did you use or do to relocate your front sigs to the forks? Looks great!
Seasoned HDF Member
Joined: Feb 2010
Posts: 5,294
Likes: 149
From: FL
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
10 Things Harley-Davidson Needs to Fix in 2026
Verdad Gallardo
May our Moderator Rest in Peace
Joined: Sep 2006
Posts: 11,386
Likes: 35
From: Rochester, NY
Congrats on the new ride, I 'may' be considered prejudiced because I have one too.
But IMHO it's one of, if not the best looking bikes HD has ever made.
As for the turn signals you can easily go one of two ways.
HD makes a relocation kit, but its not in my opinion as nice as a set of fork tube clamps you can get off e-bay for a lot less.
Here's a pic I took of mine with the HD kit on the left side (right in pic) and the tube clamp mount I got off e-bay for under $25 on the right side (left in pic).
In the pic its real easy to see how far out the HD mounts pushes the lights and if you get close to them its east to see how they don't 'fit' around the side/end of the tree as snugly as I like.
I'm sorry I can't remember if I had to take the connector apart to do the relocating, I think you do, but if you do here's a pic of the connector to help you get the wires back in the right place.
And if you don't like the way the wires look, check out the DIY thread at the top of the page.
I put a write up in there showing how to cover them up with some mesh to make them look a little nicer.
Stock turn signal wire on the left and my mesh covered one on the right.
Too bad you didn't get the stock seat with it, your wife would have LOVED it, mine does.
So I'm stuck with it, but its OK, I like how it feels too.
Good luck and ride safe.
But IMHO it's one of, if not the best looking bikes HD has ever made.
As for the turn signals you can easily go one of two ways.
HD makes a relocation kit, but its not in my opinion as nice as a set of fork tube clamps you can get off e-bay for a lot less.
Here's a pic I took of mine with the HD kit on the left side (right in pic) and the tube clamp mount I got off e-bay for under $25 on the right side (left in pic).
In the pic its real easy to see how far out the HD mounts pushes the lights and if you get close to them its east to see how they don't 'fit' around the side/end of the tree as snugly as I like.
I'm sorry I can't remember if I had to take the connector apart to do the relocating, I think you do, but if you do here's a pic of the connector to help you get the wires back in the right place.
And if you don't like the way the wires look, check out the DIY thread at the top of the page.
I put a write up in there showing how to cover them up with some mesh to make them look a little nicer.
Stock turn signal wire on the left and my mesh covered one on the right.
Too bad you didn't get the stock seat with it, your wife would have LOVED it, mine does.
So I'm stuck with it, but its OK, I like how it feels too.
Good luck and ride safe.
Last edited by In Memoriam Citoriplus; Jun 10, 2012 at 05:22 PM.
