411: Custom Dynamics Plasma Rods install - 2012 FLHX
Thread Starter
|
Road Captain
Joined: Sep 2007
Posts: 500
Likes: 2
From: Springfield Ohio
411: Custom Dynamics Plasma Rods install - 2012 FLHX
EDIT: 12-Mar-2013
Document updated to add a few of smittyc's observations.
I think I found a reasonable file sharing solution. I have uploaded the document to DepositFiles.
Filename: LED and Plasma Rods Installation - 031113.pdf
File size: 1.08MB
D/L Link: http://depositfiles.com/files/eu316df4m
If there is anything that needs attention let me know and I'll get it corrected
Please give some feedback.
(Thx smittyc for pointing out the broken file link and for his feedback on the instructions!)
original post
vvvvvvvvvvvvvvvvv
Though the questions have been asked hundreds of times in nearly every HD oriented forum out there, clear answers about "How do I wire...., Do I need..." are still hard to come by.
The most fuzzy subject I have seen concerns wiring Plasma Rods for Run/Brake/Turn operation. According to this guide (pg 2) from the Custom Dynamics site, you do NOT need an extra module to do this if you have a factory tri-bar light and DO NOT have a center tail light... just 2 PDCs (item TFC3 Dual Converter for 2010-2012 Street Glide and Road King)
http://www.customdynamics.com/instru..._rod_extra.pdf
[yes, its say "plama", not "plasma"]
Based on the conversation I had with Sean at Custom Dynamics, today I ordered the GEN200-KIT-1157 LED turn signal kit, two 8 inch rods and 2 TFC3 converters. I plan do do a full write up with pictures, wiring and wire routing to, hopefully, put this issue to bed for many folks still afraid to make the purchase.
Document updated to add a few of smittyc's observations.
I think I found a reasonable file sharing solution. I have uploaded the document to DepositFiles.
Filename: LED and Plasma Rods Installation - 031113.pdf
File size: 1.08MB
D/L Link: http://depositfiles.com/files/eu316df4m
If there is anything that needs attention let me know and I'll get it corrected
Please give some feedback.(Thx smittyc for pointing out the broken file link and for his feedback on the instructions!)
original post
vvvvvvvvvvvvvvvvv
Though the questions have been asked hundreds of times in nearly every HD oriented forum out there, clear answers about "How do I wire...., Do I need..." are still hard to come by.
The most fuzzy subject I have seen concerns wiring Plasma Rods for Run/Brake/Turn operation. According to this guide (pg 2) from the Custom Dynamics site, you do NOT need an extra module to do this if you have a factory tri-bar light and DO NOT have a center tail light... just 2 PDCs (item TFC3 Dual Converter for 2010-2012 Street Glide and Road King)
http://www.customdynamics.com/instru..._rod_extra.pdf
[yes, its say "plama", not "plasma"]
Based on the conversation I had with Sean at Custom Dynamics, today I ordered the GEN200-KIT-1157 LED turn signal kit, two 8 inch rods and 2 TFC3 converters. I plan do do a full write up with pictures, wiring and wire routing to, hopefully, put this issue to bed for many folks still afraid to make the purchase.
Last edited by basselope; Mar 12, 2013 at 06:09 PM. Reason: latest draft uploaded
Thread Starter
|
Road Captain
Joined: Sep 2007
Posts: 500
Likes: 2
From: Springfield Ohio
Iceman24, Esoumm1, Skratch... the list of folks who's opinions, pics, vids and experiences I referred to before making my choice goes on and on. The 1/4 round mounting idea is pure genius!
Don't be surprised if I come to you for more opinions before this is over!
Thanks guys!
BTW, if you're ready to make a purchase from CD shoot me an IM. I have a 5% code I'm not likely to use. Someone might as well get some good out of it!
Last edited by basselope; Sep 5, 2012 at 06:22 PM.
Tourer
Joined: Oct 2010
Posts: 383
Likes: 4
From: Bel Air, MD
Just did mine as run/turn/brake a couple weeks ago and I tied into the tri bar light. I have a 2012 FLHX. I also did the 1157 LED rear turn signals with the signal stabilizer. I udes the 3/4" round trim as well (used the composite trim since it's weather resistant). Turned out great!
Road Warrior
Joined: Dec 2006
Posts: 1,321
Likes: 12
From: Shorewood IL
I plan on doing something similar this winter to my 2012 RGC. I have CD clusters (with amber turns) from my 2007 that I want to use and I would like to purchase the run/brake/turn plasma rods from CD (with amber turns). Getting it all to work with the module on the back of the tri bar light has me somewhat stumped at the moment though. I hope to upgrade the LED's in the tri bar, bag spoilers, and tour pack spoiler, wiring them all for run/brake. Installing the clusters and plasma rods for run/brake/turn and keeping it all as clean as can be. I might be a little goofy, but I like the amber turns as opposed to the red. I think they stand out more as far as my intentions to other riders/cagers. JMHO....
Trending Topics
Thread Starter
|
Road Captain
Joined: Sep 2007
Posts: 500
Likes: 2
From: Springfield Ohio
"Low Intensity Red Running, High Intensity Red Brake, High Intensity Yellow Turn Signal - All in one Sleek Plasma Rod
Dual Converters Included, No Modules Required
Wiring is a Simple as Connecting Orange Wire to Running Light, Red Wire to Brake Light, Yellow Wire to Turn, Black to Ground"
I'll leave the rest alone since all of my info is still theoretical at this point.
Be sure to keep us updated... and post some pics so we can all be jealous!
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
10 Things Harley-Davidson Needs to Fix in 2026
Verdad Gallardo
Cruiser
Joined: Oct 2011
Posts: 204
Likes: 26
From: Tennessee
You're talking about the dual color plasma rods, right? According to the CD website:
"Low Intensity Red Running, High Intensity Red Brake, High Intensity Yellow Turn Signal - All in one Sleek Plasma Rod
Dual Converters Included, No Modules Required
Wiring is a Simple as Connecting Orange Wire to Running Light, Red Wire to Brake Light, Yellow Wire to Turn, Black to Ground"
I'll leave the rest alone since all of my info is still theoretical at this point.
Be sure to keep us updated... and post some pics so we can all be jealous!
"Low Intensity Red Running, High Intensity Red Brake, High Intensity Yellow Turn Signal - All in one Sleek Plasma Rod
Dual Converters Included, No Modules Required
Wiring is a Simple as Connecting Orange Wire to Running Light, Red Wire to Brake Light, Yellow Wire to Turn, Black to Ground"
I'll leave the rest alone since all of my info is still theoretical at this point.
Be sure to keep us updated... and post some pics so we can all be jealous!