When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I became very worried about my bike ('09 Ultra with 45,500 miles) since it had the same symptoms as the OP from the thread link above. I dropped off my bike to the dealer who said so far my IPB is shot, the "compensator is showing wear", and "the tech said he can hear grinding just by turning my rear wheel by hand". They're tearing into the transmission to diagnose for sure what needs to be done. So far I've authorized three hours of labor to diagnose the issues (the labor will be part of the repairs, not in addition to the repair)
I'm really upset about this repair - my local dealers are all owned by the same people and while I trust their work the pricing is often high. Labor in Vegas is high in general at about $100/hr. I don't have an indy that I trust. I know there are a few around but I don't get a good vibe from the couple I've spoken to in the past so I'm kinda stuck with the dealer since this isn't a repair I want to or have time to do on my own.
A well maintained 45,000 mile bike shouldn't need this much work.
Get rid of the auto primary chain tensioner, it is what causes most of these issues.
set some free play in the primary chain, like 1/2" like the old bikes, and that wear will be much less.
They added an inch to the main shaft of the trans with smaller trap door bearings, and the same size IPB, and the auto tensioner, that takes all of the slack of the chain out, when it used to be 1/2" cold. THIS IS WHY THERE ARE SO MANY PROBLEMS.
I became very worried about my bike ('09 Ultra with 45,500 miles) since it had the same symptoms as the OP from the thread link above. I dropped off my bike to the dealer who said so far my IPB is shot, the "compensator is showing wear", and "the tech said he can hear grinding just by turning my rear wheel by hand". They're tearing into the transmission to diagnose for sure what needs to be done. So far I've authorized three hours of labor to diagnose the issues (the labor will be part of the repairs, not in addition to the repair)
I'm really upset about this repair - my local dealers are all owned by the same people and while I trust their work the pricing is often high. Labor in Vegas is high in general at about $100/hr. I don't have an indy that I trust. I know there are a few around but I don't get a good vibe from the couple I've spoken to in the past so I'm kinda stuck with the dealer since this isn't a repair I want to or have time to do on my own.
A well maintained 45,000 mile bike shouldn't need this much work.
I'll post an update when I have one
Very sorry to here this, curious to see how much it cost, I maybe in the
same boat, thinking of doing it myself though.
Bummer! Shouldn't need to tear into the trans for just the bearing?? I'm kind'a worried about the ipb because of the auto adjuster??? Wish I would of done Hayden M6 when I did SE compensator. Good luck!
I bet the dealers little eyes lit up when you dropped the bike off for this, ka-ching!
Yup, my friend took his bike in because the shift lever kept coming off under warranty (2011 with 15k on the clock)....you should see the laundry list of things they changed to include the stator, primary tensioner, as many bearings as they could get away with all under the guise of the ESP......shameful....
Well, I'll know more possibly tomorrow. When I dropped it off the service writer asked me at least twice if I had the extended warranty. I knew I was in for it at that point.
All the above precisely why I "spent" the money for the Extended Warranty. 40K on my 2010 StreetGlide with no problems of any significance so far, however................
All the above precisely why I "spent" the money for the Extended Warranty. 40K on my 2010 StreetGlide with no problems of any significance so far, however................
Yup me too, I just signed up for 3 more years.....these bikes have too many things that can sneak up on ya and I need to know I'm covered.
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Slideshow: The bar-and-shield logo shows up on far more than motorcycles, some of the company's most unexpected products have nothing to do with riding.
Slideshow: From the troubled AMF years to modern misfires, these bikes earned reputations for reliability issues, questionable engineering, or disappointing performance.
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Slideshow: The Swiss custom shop has taken a Harley Softail and stretched it into something so long and low that it looks closer to a rolling sculpture than a conventional motorcycle.
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Slideshow: A standard cruiser becomes an intricate metal canvas in the hands of a Swiss custom house known for pushing Harley-Davidson platforms far beyond their factory brief.
Slideshow: Harley-Davidson's challenges aren't abstract; they show up in dropping shipments, shrinking dealer traffic, and strategic decisions that aren't yet translating into growth.