Harley Davidson Forums
Disassembled the pushrod cover to replace the inside o ring.
Disassembled the pushrod cover to replace the inside o ring.
0 2017/02/05 20:37:40
I fought these springs so I used coated plier handles to push down so I could install the clips.
I fought these springs so I used coated plier handles to push down so I could install the clips.
0 2017/02/05 20:37:44
Pushrod covers assembled.
Pushrod covers assembled.
0 2017/02/05 20:37:49
Don't know why this came up twice.
Don't know why this came up twice.
0 2017/02/05 20:37:54
Install your rocker box gaskets and make sure the oil breather passage is covered as shown in the SM.
Install your rocker box gaskets and make sure the oil breather passage is covered as shown in the SM.
0 2017/02/05 20:37:59
Install the rocker box, then the pushrods. I used the kit supplied perfect fit pushrods, so there's no adjustment. The tapered end of the pushrods goes up.
Install the rocker box, then the pushrods. I used the kit supplied perfect fit pushrods, so there's no adjustment. The tapered end of the pushrods goes up.
0 2017/02/05 20:38:04
Make sure the push rods are at their lowest point before installing the rocker arms.
Make sure the push rods are at their lowest point before installing the rocker arms.
0 2017/02/05 20:46:02
Torque to spec like everything else.
Torque to spec like everything else.
0 2017/02/05 20:46:06
Once the rocker arms are installed it's time to install the oil breathers. Mine came with new bolts that had thread locker on them already so I didn't use any additional thread locker.
Once the rocker arms are installed it's time to install the oil breathers. Mine came with new bolts that had thread locker on them already so I didn't use any additional thread locker.
0 2017/02/05 20:46:10
Oil breathers installed and torqued.
Oil breathers installed and torqued.
0 2017/02/05 20:46:14
Installing the injectors and fuel rail/hose to the new throttle body. Also, put the flanges on the ghrottle body before you put the rubber gaskets on.
Installing the injectors and fuel rail/hose to the new throttle body. Also, put the flanges on the ghrottle body before you put the rubber gaskets on.
0 2017/02/05 20:46:17
I installed the air cleaner backing plate to the throttle body before torquing the t body bolts. Once torqued I reinstalled the sensor to the throttle body and torqued the air cleaner plate down. Make sure you have the two o rings on the back of it. I was under the impression i would have to remove an adapter plate on the intake so it would fit the larger t body but there was nothing to remove.
I installed the air cleaner backing plate to the throttle body before torquing the t body bolts. Once torqued I reinstalled the sensor to the throttle body and torqued the air cleaner plate down. Make sure you have the two o rings on the back of it. I was under the impression i would have to remove an adapter plate on the intake so it would fit the larger t body but there was nothing to remove.
0 2017/02/05 20:46:21
Reconnect all the electrical connectors.
Reconnect all the electrical connectors.
0 2017/02/05 20:46:25
Install the gaskets and the covers. The SM states the left side use short bolts and the right side uses long bolts
Install the gaskets and the covers. The SM states the left side use short bolts and the right side uses long bolts
0 2017/02/05 20:46:29
Reinstall the motor mount.
Reinstall the motor mount.
0 2017/02/05 21:00:12
Next the coil pack and wires. Remember, the smaller connector is unused but it does clip on to the plastic behind the coil pack. I forgot about this and it took me a while to realize where it went.
Next the coil pack and wires. Remember, the smaller connector is unused but it does clip on to the plastic behind the coil pack. I forgot about this and it took me a while to realize where it went.
0 2017/02/05 21:00:16
Took this oppurtunity to fill the engine oil before I forgot.
Took this oppurtunity to fill the engine oil before I forgot.
0 2017/02/05 21:00:20
Reconnect the fuel gage connector and use the clip for the wiring so it doesn't contact the motor and burn.
Reconnect the fuel gage connector and use the clip for the wiring so it doesn't contact the motor and burn.
0 2017/02/05 21:00:24
Install the two fuel tank bolts, cross under tube, and fuel line.
Install the two fuel tank bolts, cross under tube, and fuel line.
0 2017/02/05 21:00:28
Then I installed the seat cause I forgot I still had to connect the o2 sensors.
Then I installed the seat cause I forgot I still had to connect the o2 sensors.
0 2017/02/05 21:00:32
Startin to look like a bike again.
Startin to look like a bike again.
0 2017/02/05 21:00:36
My dealer said they'd warranty this (I'm a master motorcycle mechanic) so I took a pic of the mileage just for the hell of it.
My dealer said they'd warranty this (I'm a master motorcycle mechanic) so I took a pic of the mileage just for the hell of it.
0 2017/02/05 21:00:39
Replaced the exhaust gaskets with se gaskets and installed the headers with the 4 1/2 in nuts. Next I reconnected the o2 sensors.
Replaced the exhaust gaskets with se gaskets and installed the headers with the 4 1/2 in nuts. Next I reconnected the o2 sensors.
0 2017/02/05 21:06:51
Next I reinstalled the air cleaner with the 3 Allen heads.
Next I reinstalled the air cleaner with the 3 Allen heads.
0 2017/02/05 21:06:57
0 2017/02/05 21:07:03
Slide on the pipe and bracket and tighten down the 3 bracket bolts and 2 pipe to bracket nuts.
Slide on the pipe and bracket and tighten down the 3 bracket bolts and 2 pipe to bracket nuts.
0 2017/02/05 21:07:09
That's the o2 sensor connector again.
That's the o2 sensor connector again.
0 2017/02/05 21:07:15
All done.
All done.
0 2017/02/05 21:07:20
Shame to have it this dirty but hey, I wanted to ride today.
Shame to have it this dirty but hey, I wanted to ride today.
0 2017/02/07 06:56:07
0 2017/02/07 08:12:46
Like I said lol!!!! Dynas are a blank canvas.
Like I said lol!!!! Dynas are a blank canvas.
0 2017/02/08 16:22:47
Rockin fhe oem street bob seat. I made a point of buying one before we went out of state (last year) cause I knew my Badlander woulda tore my ass up like a fuckin prison inmate.
Rockin fhe oem street bob seat. I made a point of buying one before we went out of state (last year) cause I knew my Badlander woulda tore my ass up like a fuckin prison inmate.
0 2017/02/09 05:44:13
As you can see, I still have a little "fine tuning" (no pun intended) to do on the top right, and 5500-6000 rpm range. Once I fix the oil leak, I will be back at it. Once I find a good tuner in my area, I will have it dyno tuned and update everyone on the numbers. I don't want to go to a HD dealer since they tune for max "power/fuel economy" which leads me to believe it will be runnin lean/hot like it did from the factory. I'll keep you guys updated.
As you can see, I still have a little "fine tuning" (no pun intended) to do on the top right, and 5500-6000 rpm range. Once I fix the oil leak, I will be back at it. Once I find a good tuner in my area, I will have it dyno tuned and update everyone on the numbers. I don't want to go to a HD dealer since they tune for max "power/fuel economy" which leads me to believe it will be runnin lean/hot like it did from the factory. I'll keep you guys updated.
0 2017/02/11 15:32:36
0 2017/02/11 15:36:08
I use the T-pin more than anything. Go to Joann fabrics or Michaels and you can get 20 of them for a few bucks
I use the T-pin more than anything. Go to Joann fabrics or Michaels and you can get 20 of them for a few bucks
0 2017/02/13 07:56:25
0 2017/02/14 12:30:00
0 2017/02/14 13:31:49
0 2017/02/14 13:32:13
0 2017/02/14 13:32:53
Bags on
Bags on
0 2017/02/15 07:58:04
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
© 2026 MH Sub I, LLC dba Internet Brands