Basic SERT Question.
Thread Starter
|
Elite HDF Member
Joined: Sep 2007
Posts: 4,541
Likes: 1
From: Nuevo México, Los Estados Unidos de América
Basic SERT Question.
I'm getting my SERT today. Found a new one cheap online.It's part # 32107-01G. Now while the fellow I bought it off, bought it from the dealer, for an '08 he special ordered (then canceled) I'm hearing that I need to get the "J" softwear to get the maps that use the 02 sensors. Is that correct?
I also understand I need to wiring. Once it comes in I will head down to the stealer and pick those up.
Can someone give me just a general discription of how setup and install of this thing goes? Is it a "project"?
Also, I currently have the flash Stage I download, and want to richen it. I have a Big Sucker, and SEIIS. Anyone recommend a map?
Thanks. I'm new to EFI, so anyone familiar with the SERT, comments welcome.
I also understand I need to wiring. Once it comes in I will head down to the stealer and pick those up.
Can someone give me just a general discription of how setup and install of this thing goes? Is it a "project"?
Also, I currently have the flash Stage I download, and want to richen it. I have a Big Sucker, and SEIIS. Anyone recommend a map?
Thanks. I'm new to EFI, so anyone familiar with the SERT, comments welcome.
Cruiser
Joined: Apr 2006
Posts: 163
Likes: 0
From:
RE: Basic SERT Question.
1.install program to computer
2.hook up cable to computer and module
3.hook other cable to module and bike
4.pick which map you want to send to bike
5.turn key switch to "on", set switch onhandlebars to "run"
6.program ECM (do not disturb cables or bike till it says it's finished
7.turn off key switch for 10 seconds
8.go for a test drive
The SERT is brand new in the box right? Once its been hooked to a bike its keyed to that bike forever.
2.hook up cable to computer and module
3.hook other cable to module and bike
4.pick which map you want to send to bike
5.turn key switch to "on", set switch onhandlebars to "run"
6.program ECM (do not disturb cables or bike till it says it's finished
7.turn off key switch for 10 seconds
8.go for a test drive
The SERT is brand new in the box right? Once its been hooked to a bike its keyed to that bike forever.
Thread Starter
|
Elite HDF Member
Joined: Sep 2007
Posts: 4,541
Likes: 1
From: Nuevo México, Los Estados Unidos de América
RE: Basic SERT Question.
Brand new in box.
Got the SERT so I could tune my ride correclty. It's running lean, even with the stage I download it's lean.
Come spring I'm doing a high performance build, after which, I'll have it Dynod. SERT seemed, while not the easiest/cheapest, the best once I have everything done, and dynod.
Got the SERT so I could tune my ride correclty. It's running lean, even with the stage I download it's lean.
Come spring I'm doing a high performance build, after which, I'll have it Dynod. SERT seemed, while not the easiest/cheapest, the best once I have everything done, and dynod.
Tourer
Joined: Dec 2006
Posts: 314
Likes: 0
From: North Hills California
RE: Basic SERT Question.
I ran my 06 with the stg 1 download for quite a while then tried a PCIII which worked well until I went 95". The dyno shop ran my bike after the build with the PCIII removed, STG 1 flash only and it was dead rich everywhere except WOT, and that was with 9.5:1 compression, andrews 37 cams, and ported heads. You may not need to richen it up at all if it doesnt ping.
Thread Starter
|
Elite HDF Member
Joined: Sep 2007
Posts: 4,541
Likes: 1
From: Nuevo México, Los Estados Unidos de América
RE: Basic SERT Question.
The Download I have was made for a more closed pipe than I am running, and, like the stock map, the canned "street legal" maps all keep it running lean.
I get popping at decel.
I get popping at decel.
Trending Topics
Thread Starter
|
Elite HDF Member
Joined: Sep 2007
Posts: 4,541
Likes: 1
From: Nuevo México, Los Estados Unidos de América
RE: Basic SERT Question.
Nother question:
Can I change the rev. limiter with the race tuner? Right now it is set at 6.2k I think, with the stage I download. I don't want it back down at stock.
Will the SERT keep this? Allow me to ajust it? Or will it lock it back down to stock?
Thanks
Can I change the rev. limiter with the race tuner? Right now it is set at 6.2k I think, with the stage I download. I don't want it back down at stock.
Will the SERT keep this? Allow me to ajust it? Or will it lock it back down to stock?
Thanks
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Jason Momoa Is Turning Classic Harleys Into PHEVs
Verdad Gallardo
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Road Warrior
Joined: Dec 2006
Posts: 1,900
Likes: 1
From: Backwoods of NH
RE: Basic SERT Question.
ORIGINAL: Herr Monk
Brand new in box.
Got the SERT so I could tune my ride correclty. It's running lean, even with the stage I download it's lean.
Come spring I'm doing a high performance build, after which, I'll have it Dynod. SERT seemed, while not the easiest/cheapest, the best once I have everything done, and dynod.
Brand new in box.
Got the SERT so I could tune my ride correclty. It's running lean, even with the stage I download it's lean.
Come spring I'm doing a high performance build, after which, I'll have it Dynod. SERT seemed, while not the easiest/cheapest, the best once I have everything done, and dynod.
