2011 flhx alarm..
Thread Starter
|
Tourer
Joined: Mar 2008
Posts: 289
Likes: 6
2011 flhx alarm..
I searched all over, i cant store my PIN code for my alarm fob after programming it in with my turn signals...everything i have read says turn ign. to off position after i put in PIN code 5 digit, before it re-sets by it self..I did this but its not retaining the code and goes back to not having the bike start (alarm on mode) HeLP!! thanks ...or is it off to the dealer for this? later..
Thread Starter
|
Tourer
Joined: Mar 2008
Posts: 289
Likes: 6
so i have fully charged bike, new batt in fob, all bike functions work, lts, radio etc, when i approach bike the alarm red key is flashing, but the turn signal lights do not flash as they used to in the past, and when i walk away also they DO NOT flash to Arm the bike..
i tried all the on/off/on/on...TS functions...re-did code, but it wont Store in the odometer area. any other suggestions is appreciated, i feel this is the problem (no-storing of code) but after i put in code, i turned ign off,,,,i also put in code and hit Right tS once then ign off...but still no luck..
i tried all the on/off/on/on...TS functions...re-did code, but it wont Store in the odometer area. any other suggestions is appreciated, i feel this is the problem (no-storing of code) but after i put in code, i turned ign off,,,,i also put in code and hit Right tS once then ign off...but still no luck..
Thread Starter
|
Tourer
Joined: Mar 2008
Posts: 289
Likes: 6
Well i am back,,and i apologize for taking up your time for my stoopid..
after much searching and back and forth, i said to myself..."SELF" what if the new FOB battery was BAD.....soooo i open the key fob cover,,and low and behold...i installed it upside down...yikes!...so now its all good....man i hate my eyes without glasses..thanks to all for your input...time to ride...
after much searching and back and forth, i said to myself..."SELF" what if the new FOB battery was BAD.....soooo i open the key fob cover,,and low and behold...i installed it upside down...yikes!...so now its all good....man i hate my eyes without glasses..thanks to all for your input...time to ride...
Thread Starter
|
Tourer
Joined: Mar 2008
Posts: 289
Likes: 6
ok i am back...after removal and replaced TSSM, it re-set and bike started fine,,,after bike sits for a while, bike will not start, my question is, if i replace this TSSM do i need to also change the key fobs? or will it sync ok with tssm and my current key fobs? thanks
Trending Topics
Seasoned HDF Member
Joined: Jan 2007
Posts: 20,616
Likes: 4,440
From: anacoco, la
why did you change the tssm? (actually here in the states, its a hfsm, the tssm is hdi)
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Engraved Rebellion: Inside Bundnerbike's Glam Rock II
Verdad Gallardo
10 Motorcycles You Should Never Buy
Joe Kucinski
Thread Starter
|
Tourer
Joined: Mar 2008
Posts: 289
Likes: 6
sorry i didnt get my point across correctly, what i meant to say was, i disconnected the hfsm and let it sit for a while, then re-installed it, after ign on off sequence, bike started fine. then after a few hours passed i tried to start bike again and NO luck,,i was wondering if i bought a good used ebay (i know its a risk) with correct hfsm # , will i have any problem setting pin? or other issues i may need to take it to dealer for? OR can i just use pin set up as usual, ign on off ...turn sig button etc...basically plug and play? thanks..
Seasoned HDF Member
Joined: Jan 2007
Posts: 20,616
Likes: 4,440
From: anacoco, la
so are you saying that your bike originally did not have security and then you bought a hfsm off of ebay and are trying to get it married to your bike? if so, i'm pretty sure you are going to have to take it to the dealer to get your ecm flashed. i know that it is possible to go from hfsm to tsm without the dealer flash, but it takes a quite convoluted method, and leaving your bike ignition on for over a half hour (def need to have it on battery tender) but i don't know if you can do it the other way without the dealer flashing it.....
edit: check out this thread, it might answer your questions - https://www.hdforums.com/forum/touri...stall-faq.html
edit: check out this thread, it might answer your questions - https://www.hdforums.com/forum/touri...stall-faq.html
Last edited by skratch; Aug 5, 2014 at 08:33 PM.