2018 RKS front turn signal problem

Reply Subscribe

Thread Tools

Search this Thread

Apr 12, 2022 | 05:23 PM

#21

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

Dam!! This has to be the problem then. I’ll have to redo the entire job I’m sure! Do you have a 2018 road king? This sucks! Lol! I might be able to pull just that harness out through the top hole by the grips. I didn’t tie the harnesses together so it is possible but… risky. If I damage something I’ll just have to do it all again I guess. I still have to verify it is wrong first. Oh man! Thanks for all your help everyone.

Apr 12, 2022 | 05:31 PM

#22

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

What did you end up doing?

Apr 12, 2022 | 05:34 PM

#23

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

Oh sorry. You pulled the pins I see now. How did you do that. Did you pull your bars. Or did you just pull it out enough to get to the connections inside the bars. Mine are 16inch carlini gangsters. I’m not sure if that’s possible

Apr 12, 2022 | 09:11 PM

#24

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

Well that is exactly the problem!! Thank you so much. I really appreciate it! So I’ll prob just remove the bars and start over. Now!! Quick question for everyone. I broke that stupid little button on top of the left switch housing to flip through your odometer settings. Where can I buy one. Does Harley sell that button?

Apr 13, 2022 | 04:54 AM

#25

blackice bob

Stage III

Joined: May 2013

Posts: 3

Likes: 0

From: alberta

I was able to pull the wires through the top of the bars lots of extra wire on the kit, I put on 16" factory 47 bars. I used a paper clip with the end sharpened to get the pins out , there small and its a pain to get them out, Be patient . As for the button ,yes Harley sells them and there cheap, I had to replace mine also, Good luck

Apr 14, 2022 | 08:06 AM

#26

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

So yeah. Pulled the bars and the namz harness is pinned wrong. Super pissed!! Here’s what I don’t understand though if someone could help. At the bottom of the factory harnesses, left and right all end up being pinned 1,2,3. I suppose it doesn’t matter if they all have pins connected going up to the turn signal? Is that correct? Also, at the bottom where they plug in behind the headlight, you plug in the male connector with three wires but at the back of the female connector there are 4 wires coming out. Then they all run together and go under the tank from there. Why is ther 4?

Apr 22, 2022 | 12:29 PM

#27

Bigsean

Thread Starter

Novice

Joined: Apr 2022

Posts: 18

Likes: 1

From: Minnesota

So just to end this thread. I did talk with namz and they sent me new harnesses. Got the bars back on and all is good. If anyone has any questions about putting 16inch carlinis on a road king special I would love to help. Thanks to all!

Nov 29, 2023 | 10:23 AM

#28

Lowendtorque

5th Gear

Joined: May 2021

Posts: 9

Likes: 3

From: Libya

Quote:

Originally Posted by Bigsean

Codes B2141 and B2146. I didn’t check fuses though because because someone on here said it doesn’t have fuses for the blinkers or an old school relay either. All controlled through one of the BCMs. I will look in there though just to be sure.

hi, I got the front left turn signal code as the light bulb stopped working. I since replaced it and the engine light and code persist. What do I do now to cancel it? Many thanks