Help with Clevis bolt
Grand HDF Member
Joined: Apr 2007
Posts: 3,726
Likes: 3,071
From: Brighton, MI
I agree with a little heat. I bet loctite is involved.
Concern is damaging paint with the heat. So I am in the camp of heating the clevis. I also agree, use allen side to just hold in place and try to twist off clevis. Looks, like a bar (long screw driver etc.) can go into the holes of the clevis to act as a wrench.
Mildly heat the clevis and let the heat sink back to the threads of the bolt. Allen on the bolt, rod, screw driver or wrench on the clevis and keep trying. Heat, attempt to turn off, heat a little more, etc. You will get it off. Close fitting allen wrench (or nut and bolt) in the clevis hole and a pipe over the allen wrench or bolt for leverage. Good luck.
Concern is damaging paint with the heat. So I am in the camp of heating the clevis. I also agree, use allen side to just hold in place and try to twist off clevis. Looks, like a bar (long screw driver etc.) can go into the holes of the clevis to act as a wrench.
Mildly heat the clevis and let the heat sink back to the threads of the bolt. Allen on the bolt, rod, screw driver or wrench on the clevis and keep trying. Heat, attempt to turn off, heat a little more, etc. You will get it off. Close fitting allen wrench (or nut and bolt) in the clevis hole and a pipe over the allen wrench or bolt for leverage. Good luck.
Seasoned HDF Member
Joined: Mar 2010
Posts: 21,114
Likes: 7,638
From: Poolville
Apparently that's a socket cap bolt. Try a 5/16 Allen on the inside and stable it with a medium breaker bar to hold it in place.. With a very large 15" crescent wrench you should be able to unscrew the support part of the foot peg assembly off of the bolt by holding the bolt in position and turning the support.
Last edited by 98hotrodfatboy; Dec 28, 2024 at 02:14 PM.
Seasoned HDF Member
Joined: May 2008
Posts: 21,173
Likes: 12,740
From: South Carolina
1/2-20 Bolt, 3/8 allen head.
Put the footpeg back on, fold it up and then hit it with a 5 pound deadblow mallet.
This location was a very poor choice for an allen head fastener, and the factory is still using allen heads in bad locations.
Put the footpeg back on, fold it up and then hit it with a 5 pound deadblow mallet.
This location was a very poor choice for an allen head fastener, and the factory is still using allen heads in bad locations.
Last edited by Dan89FLSTC; Dec 28, 2024 at 02:52 PM.
Thread Starter
|
Road Captain
Joined: Jan 2008
Posts: 715
Likes: 81
From: London, UK
Guys,
Thanks for all the help. It must have had loctite I think. I put the torch on the clevis, the peg back into the clevis and with a little persuasion with my rubber mallet it turned.
Appreciate all the ideas.
Happy New Year and Ride safe all.
Thanks for all the help. It must have had loctite I think. I put the torch on the clevis, the peg back into the clevis and with a little persuasion with my rubber mallet it turned.
Appreciate all the ideas.
Happy New Year and Ride safe all.
Seasoned HDF Member
Joined: May 2008
Posts: 21,173
Likes: 12,740
From: South Carolina
Thread Starter
|
Road Captain
Joined: Jan 2008
Posts: 715
Likes: 81
From: London, UK
Exactly that
..this thing aint spinning on its own for sure ! 😉😁
Thread
Thread Starter
Forum
Replies
Last Post
